How many swapped guys are in here?

[justpball]

yea details bro? i am fixing to put a 5.3 in mine...what did you do about wiring?

[SBTork]

Originally Posted by justpball

yea details bro? i am fixing to put a 5.3 in mine...what did you do about wiring?

also curious....

[onedayjake]

I'm running a 4L60E because I like to be able to control shift points and my 5.3 is drive by wire. At first I didn't think I'd like the DBW but I've gotten used to it and I like it a lot now. I did the wiring myself and it really wasn't that bad. I had to use a painless auxiliary fuse box, it had seven fuses, to run the injectors, coils, O2's... When I get more time I'll post more pics. Any other questions feel free to ask. I would do this swap again in a heartbeat, it runs awesome! I just wish I would have started with a better shell.

[Da88burban]

Got anymore pics of the burb?

[onedayjake]

Originally Posted by Da88burban

Got anymore pics of the burb?

With ugly 80's stripes, ew.

Without, yay!


I've got new tires on the way, I need a bunch of front end work, ball joints, idler arm... So I'm going to cut a coil or so off of the front springs to bring it down a bit. I'm also getting some patch panels so I'm trying to decide whether to paint it all satin black or keep it white. I'm leaning toward white only because there are so many people "murdering" everything anymore.

[iluvmy72]

Originally Posted by onedayjake

I'm running a 4L60E because I like to be able to control shift points and my 5.3 is drive by wire. At first I didn't think I'd like the DBW but I've gotten used to it and I like it a lot now. I did the wiring myself and it really wasn't that bad. I had to use a painless auxiliary fuse box, it had seven fuses, to run the injectors, coils, O2's... When I get more time I'll post more pics. Any other questions feel free to ask. I would do this swap again in a heartbeat, it runs awesome! I just wish I would have started with a better shell.

OK....so you didn't have to use the harness from painless? I am doing a similar swap but I am using a vortec 454 from a 1998 2500 in my 1991 burb. But you probably ran into the same issues as I am about to. I have been told I can't use the stock harness and have to go with a custom made one from painless or Howell. These are Howell techs that have told me this and I almost believed them until I saw this post. If you used the stock version, I'd like to see pics on how you ran your dash connections with as much info as you can give. I will contact painless on their "auxiliary fuse box" thing a ma jig and see if it can work for me. Did you need your computer to be re-programmed? I am so close to finishing my burb. The vortec 454 is in along with the computer. I need to put the 4L80E tranny and NP-241C transfer case(passenger side drop) in and finish the wireing. The wireing is my biggest hold up so far. But I have the ODB2cats ready for the dual exhaust setup as well as all four 02 sensors that are brand new. What else can I be missing?

[onedayjake]

Originally Posted by iluvmy72

OK....so you didn't have to use the harness from painless? I am doing a similar swap but I am using a vortec 454 from a 1998 2500 in my 1991 burb. But you probably ran into the same issues as I am about to. I have been told I can't use the stock harness and have to go with a custom made one from painless or Howell. These are Howell techs that have told me this and I almost believed them until I saw this post. If you used the stock version, I'd like to see pics on how you ran your dash connections with as much info as you can give. I will contact painless on their "auxiliary fuse box" thing a ma jig and see if it can work for me. Did you need your computer to be re-programmed? I am so close to finishing my burb. The vortec 454 is in along with the computer. I need to put the 4L80E tranny and NP-241C transfer case(passenger side drop) in and finish the wireing. The wireing is my biggest hold up so far. But I have the ODB2cats ready for the dual exhaust setup as well as all four 02 sensors that are brand new. What else can I be missing?

Oh I think it's such a shame people waste so much money on an aftermarket harness. I'm fortunate enough to work in a shop that has Alldata so wiring diagrams were easy for me to print out for both trucks and weed out what I didn't need. The PCM itself just needs battery positive, ignition positive and grounds. Alot of the harness is self contained. You will need to run some wires inside for the data link connector, tach, etc.
This is the fuse block I used I think or one like it.
http://www.jegs.com/i/Painless+Perfo...70107/10002/-1
I did have to program the theft out of the PCM, I did it with HP tuners.