|
04-18-2011, 07:59 AM
|
#1 |
|
Registered User
Join Date: Mar 2010
Location: Texarkana Texas
Posts: 40
|
65 front hubs
I can't seem to find new front inner hub seals. I even got the wrong ones from LMC. The old seal was different from any seal i've seen. Unfortunately I threw them both away thinking i would get the right ones from LMC. Anyone else ran into this problem?
|
|
|
|
04-18-2011, 08:09 AM
|
#2 |
|
Registered User
Join Date: Mar 2010
Location: Texarkana Texas
Posts: 40
|
Re: 65 front hubs
here is the back of the hub, the seal pressed in to the larger outer ring instead of where the bearing race pressed into
|
|
|
|
|
04-19-2011, 12:42 AM
|
#3 |
|
60-66 Nut
  Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 23,246
|
Re: 65 front hubs
Have you checked with your local auto parts supplier? I looked them up on O'Reilly's site and it shows the front seals to be National #9015S. If you don't have an O'Reilly's close by, another store should be able to cross reference that number, unless you find someone willing to look it up themselves.
__________________
Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE |
|
|
|
|
04-19-2011, 07:56 AM
|
#4 |
|
Registered User
Join Date: Mar 2010
Location: Texarkana Texas
Posts: 40
|
Re: 65 front hubs
Ive Texarkana with the hub in hand. I keep getting a seal that fits where the bearing presses in which is not right. The inner seal hole won't fit over the spindle.
|
|
|
|
|
04-19-2011, 11:23 AM
|
#5 |
|
Senior Enthusiast
Join Date: Feb 2007
Location: Spokane Valley, WA
Posts: 8,356
|
Re: 65 front hubs
You might try part number NOS 19757 from Napa. No way to tell from a photo if it's correct or not. Unfortunately they just "upgraded" their site, so links directly to the search results no longer work.
|
|
|
|
|
04-19-2011, 10:31 PM
|
#6 |
|
Registered User
Join Date: Jun 2010
Location: gadsden, alabama
Posts: 468
|
Re: 65 front hubs
checked autozone,oreillys,and advanced auto parts all give the same specs and part no#s
Part # 9015S Shaft Size: 2 in. (50.8 mm.) Housing Bore: 2.561 in. (65.05 mm.) Outside Diameter: 2.565 in. (65.15 mm.) Width: 0.549 in. (13.94 mm.) Material: Nitrile might want to check your spindle diameter and hub bore sizes and compare
__________________
Due to financial constraints, the light at the end of the tunnel will be shut off until further notice |
|
|
|
|
04-20-2011, 12:16 AM
|
#7 |
|
60-66 Nut
Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 23,246
|
Re: 65 front hubs
It's been a while since I've had a seal out of one of these original hubs, but I believe the seal is supposed to fit into the same bore as the inner bearing.
__________________
Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
