best fitting headers, 4x4 4spd - The 1947 - Present Chevrolet & GMC Truck Message Board Network

8mag · 07-20-2003, 12:26 AM

need opinons on headers. built a new 400 sb, vortec heads, erson cam,9to1 compression. have corvette ramshorns and 21/2inch dual into single 70 series 3inch flowmaster. very quiet and not as much power as i had hoped. wandering-wanting to go the header route and change to 2 magnaflow mufflers. any power difference? what is the best fitting header for a 4x4 ,4spd truck. please help

JayDubBlazer · 07-20-2003, 05:34 AM

I have no personal expericnce but reader a thread a while back the dynomax cermic coated headers got good reviews. they are about 230 bucks at jegs or summit.

8mag · 07-20-2003, 06:41 PM

btt

Glen · 07-20-2003, 11:39 PM

The Dynomax headers mentioned above will not work on a 4 speed, I just found out the hard way this weekend. I wish they would fit, I would love to swap you for those manifolds.....

**'68OrangeSunshine** · 07-21-2003, 02:55 AM

I have Heddman Hedders on a crate 350 in my '71 GMC Jimmy, w/SM465.
The Heddmans fit OK, but are a little close around the starter. To replace it, you have to pull the Pass side hedder. I had to reconfigure the Z/bar on the driver's side to clear the collector down tubes, but that might have been due to the different throw-out geometry for a Centerforce II clutch. I was on a budget at the time I got this truck back on the road and the Heddman's were on sale. It's been a daily driver for 4 years.

**JIMs70GMC** · 07-21-2003, 05:32 AM

I read somewhere that the tri-ys from doug Thourley (sp) fit around the z-bar and were made for our trucks. Pricey though close to $400.

Brewski* · 07-21-2003, 09:14 AM

I went with the Ceramic Coated Hedman. It is the only one that fit on my truck. Had to have Summit order them special. I tried the Elite set from Hedman but they would not clear the linkage on the 4x4 4speed 350

07-20-2003, 12:26 AM	#1
8mag Registered User Join Date: Jun 2001 Location: nampa idaho,usa Posts: 92	best fitting headers, 4x4 4spd need opinons on headers. built a new 400 sb, vortec heads, erson cam,9to1 compression. have corvette ramshorns and 21/2inch dual into single 70 series 3inch flowmaster. very quiet and not as much power as i had hoped. wandering-wanting to go the header route and change to 2 magnaflow mufflers. any power difference? what is the best fitting header for a 4x4 ,4spd truck. please help __________________ 1972 3/4 4x4,14bolt locker rear, dana44 lock right front, sm465, sb 400, blazer tank,dual batterys,3"lift,32-9.00-16 super swampers daily driver other trucks 1972 1 ton dually 4x4,454 4 spd,,235-85-16, flat bed front and rear winches, rear gas tank and under bed gun safe.tilt wheel

07-20-2003, 05:34 AM	#2
JayDubBlazer go cyclones Join Date: Jun 2003 Location: Ames, IA Posts: 1,885	I have no personal expericnce but reader a thread a while back the dynomax cermic coated headers got good reviews. they are about 230 bucks at jegs or summit. __________________ Wes PROJECT OLE GREEN 1972 Blazer 4X4 350/700R4 2017 Silverado LT

07-20-2003, 06:41 PM	#3
8mag Registered User Join Date: Jun 2001 Location: nampa idaho,usa Posts: 92	btt __________________ 1972 3/4 4x4,14bolt locker rear, dana44 lock right front, sm465, sb 400, blazer tank,dual batterys,3"lift,32-9.00-16 super swampers daily driver other trucks 1972 1 ton dually 4x4,454 4 spd,,235-85-16, flat bed front and rear winches, rear gas tank and under bed gun safe.tilt wheel

07-21-2003, 02:55 AM	#5
'68OrangeSunshine Senior Member Join Date: Feb 2002 Location: Tucson, AZ USA Posts: 7,210	I have Heddman Hedders on a crate 350 in my '71 GMC Jimmy, w/SM465. The Heddmans fit OK, but are a little close around the starter. To replace it, you have to pull the Pass side hedder. I had to reconfigure the Z/bar on the driver's side to clear the collector down tubes, but that might have been due to the different throw-out geometry for a Centerforce II clutch. I was on a budget at the time I got this truck back on the road and the Heddman's were on sale. It's been a daily driver for 4 years. __________________ Every 25 years I like to rebuild that 292, whether it needs it or not.

07-21-2003, 05:32 AM	#6
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	I read somewhere that the tri-ys from doug Thourley (sp) fit around the z-bar and were made for our trucks. Pricey though close to $400. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

07-20-2003, 11:39 PM	#4
Glen Registered User Join Date: Jan 2003 Location: Chandler, AZ Posts: 189	The Dynomax headers mentioned above will not work on a 4 speed, I just found out the hard way this weekend. I wish they would fit, I would love to swap you for those manifolds.....

07-21-2003, 09:14 AM	#7
Brewski* Registered User Join Date: Aug 2001 Location: Rocky Mount, MO Posts: 1,293	I went with the Ceramic Coated Hedman. It is the only one that fit on my truck. Had to have Summit order them special. I tried the Elite set from Hedman but they would not clear the linkage on the 4x4 4speed 350



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.