|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
07-16-2011, 02:39 AM
|
#1 |
|
Registered User
Join Date: Jul 2009
Location: washington
Posts: 4,178
|
will a 95 rearend fit?
http://seattle.craigslist.org/sno/pts/2494250133.html
if it fits it ships! i neeeed posi and 3:73 i will check and verify of coarse. i have a spare 3.08 open ten bolt from an 85 sitting right now. will the parts cross over? thanks
__________________
377 sbc thumpr cam autogear m23 muncie 3:73 Detroit trutrac 3''spintech prostreet mufflers xpipe 1 3/4 headers build thread !http://67-72chevytrucks.com/vboard/s...d.php?t=577217 Iroc gauge threadhttp://67-72chevytrucks.com/vboard/s...d.php?t=554511 |
|
|
|
07-16-2011, 08:24 PM
|
#2 |
|
Registered User
Join Date: Jul 2009
Location: washington
Posts: 4,178
|
Re: will a 95 rearend fit?
nobody knows?
__________________
377 sbc thumpr cam autogear m23 muncie 3:73 Detroit trutrac 3''spintech prostreet mufflers xpipe 1 3/4 headers build thread !http://67-72chevytrucks.com/vboard/s...d.php?t=577217 Iroc gauge threadhttp://67-72chevytrucks.com/vboard/s...d.php?t=554511 |
|
|
|
|
07-16-2011, 08:55 PM
|
#3 |
|
Registered User
Join Date: Feb 2007
Location: Austin, TX
Posts: 3,930
|
Re: will a 95 rearend fit?
Some info here. http://67-72chevytrucks.com/vboard/s...d.php?t=396824
Looks like you might have an axle spline count mismatch.
__________________
1977 GMC Sierra Grande |
|
|
|
|
07-16-2011, 09:42 PM
|
#4 |
|
Senior Member
Join Date: May 2004
Location: Caldwell,Tx.
Posts: 3,648
|
Re: will a 95 rearend fit?
You also need to know if the rear end pictured is an 8.5" 10 bolt or a 14 bolt. They used both under those trucks . 1/2 tons had both but light duty 3/4 tons had the 14 bolt. Basically the same rear as a 90-93 454SS Truck but with 6 lugs. Since it has 3.73's it most likely came fron a 6 lug light duty 3/4 ton truck. If you buy the whole rear you can just have the axles redrilled or install Mosier replacement axles and will have a pretty strong rear. The 88-99 truck rears were only slightly wider . Barely noticeable.
Frank
__________________
Born and proudly residing in a Red State ! |
|
|
|
|
07-17-2011, 03:49 AM
|
#5 | |
|
Registered User
Join Date: Jul 2009
Location: washington
Posts: 4,178
|
Re: will a 95 rearend fit?
Quote:
__________________
377 sbc thumpr cam autogear m23 muncie 3:73 Detroit trutrac 3''spintech prostreet mufflers xpipe 1 3/4 headers build thread !http://67-72chevytrucks.com/vboard/s...d.php?t=577217 Iroc gauge threadhttp://67-72chevytrucks.com/vboard/s...d.php?t=554511 |
|
|
|
|
|
07-17-2011, 09:35 AM
|
#6 |
|
Registered User
Join Date: Jul 2007
Location: Ontario Canada
Posts: 1,006
|
Re: will a 95 rearend fit?
Yes they are 30 spline , you can use the guts for sure with the conversion bearings and I have been told you can take about 1/16 of an inch off the newer axles and they will work also . you can also buy 30 spline axles for our trucks
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
