The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > All 4x4 Tech & Off Roading

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 08-21-2011, 08:14 AM   #1
72longbed
Account Suspended
 
72longbed's Avatar
 
Join Date: Jun 2003
Location: PA
Posts: 1,411
Question Shortening a drag link??

Before I do this I was wondering if anybody on here has ever had to cut a section of drag link to shorten the overall length? My two halves are run in all the way to touching each other, and I need to shorten the link another 1" or so to align the steering wheel properly.

Are these babies made of super hard steel that my sawzall blades wont cut or can it be done easily?

Thanks for your input.

72longbed
72longbed is offline   Reply With Quote
Old 08-21-2011, 08:28 AM   #2
special-K
Special Order

 
special-K's Avatar
 
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,862
Re: Shortening a drag link??

You have to do that with a 4" lift? I've always had to back the ends apart to get the steering box centered with the steering on the axle. Then,remove steering wheel and install so it sits right.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed"

GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project)
GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling)
Tim

"Don't call me a redneck. I'm a rough cut country gentleman"

R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~
special-K is offline   Reply With Quote
Old 08-21-2011, 08:39 AM   #3
72longbed
Account Suspended
 
72longbed's Avatar
 
Join Date: Jun 2003
Location: PA
Posts: 1,411
Re: Shortening a drag link??

Yep. Looked over the situation , and that seems to be what's limiting my adjustment to the steering wheel. It's a TRW draglink and I don't know if the parts counter kid gave me a "longer" than what I needed link, but that would give me what I needed if I shorten it.

Is it going to be a 'bear' to cut?

I have thin cutoff disks for my grinder also. Thinking I might be able to leave it in place and just cut off one side where the adjuster collar allows me into one shaft. Rotate the adjuster collar to finish the cut.

What'cha think?

Last edited by 72longbed; 08-22-2011 at 04:17 PM.
72longbed is offline   Reply With Quote
Old 08-21-2011, 09:36 AM   #4
LONGHAIR
just can't cover up my redneck
 
Join Date: May 2004
Location: Columbus OH
Posts: 11,414
Re: Shortening a drag link??

Compare your old drag link to the new one first.
An inch sound like a lot of adjustment, it is usually only a few turns.

Personally, I wouldn't go cutting on the drag link unlees it was absolutely necessary....and even at that I would cut a little as possible equally from each side. You need to maintain maximum contact with the threads.
__________________
You can review the site's rules here.



Quote:
Originally Posted by Longhorn Man View Post
As for reading directions...
The directions are nothing but another man's opinion.
Learn from the mistakes of others, you won't live long enough to make them all yourself...

Bad planning on your part does not necessarily constitute an instant emergency on my part....

The great thing about being a pessimist is that you are either pleasantly surprised or right.
LONGHAIR is offline   Reply With Quote
Old 08-22-2011, 06:34 AM   #5
special-K
Special Order

 
special-K's Avatar
 
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,862
Re: Shortening a drag link??

I would remove the ends and put in a vise. I'd take some off both sides.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed"

GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project)
GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling)
Tim

"Don't call me a redneck. I'm a rough cut country gentleman"

R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~
special-K is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:31 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com