|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
09-13-2011, 10:46 PM
|
#1 |
|
Registered User
Join Date: Apr 2008
Location: Imperial Beach, CA
Posts: 1,040
|
5k rpm in a few seconds
No 1/4 or 1/8 time yet but per the gear calculator with 3.70 gears and a th400 it's 110mph at 5k. I hit 5k in 3rd from a dead stop in 9sec. This don't seem right unless my engine build put a bigger cam in it then he told me.
Posted via Mobile Device
__________________
69 c-10 BBC  462ci, forged crank, H-beam rods, 10.5-1 KB forged pistons, Dart Iron Eagle 308cc, Straub Cam, Comp Cams chrome moly full rollers, Weiand Team G, Prosystems 950, TH400/3500 Dalenzie stall, Currie 9+ Detroit Locker w/31spline axles.  3.5/6in drop. My Build.
|
|
|
|
09-14-2011, 02:08 PM
|
#2 |
|
Registered Truck Offender
Join Date: May 2008
Location: hells training ground (aka Ariz)
Posts: 3,118
|
Re: 5k rpm in a few seconds
I don't think your allowing for that big block driving through that convertor about 2-3 thousand RPM are you LOL
__________________
Still playin with trucks, even at my age! When you're dead, it's only a problem for the people around you, because you don't know you're dead. .....It's kinda the same when your STUPID. I just did my taxes and reviewed my SS statement. Thanks to the current administration it looks like I will only have to work till noon on the day of my funeral. |
|
|
|
|
09-14-2011, 07:29 PM
|
#3 |
|
Registered User
Join Date: Feb 2001
Location: Wetumpka, Al, U.S.
Posts: 8,892
|
Re: 5k rpm in a few seconds
I think Marv may be on to something. What do you have for a convertor?
__________________
Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole! |
|
|
|
|
09-15-2011, 04:47 PM
|
#4 |
|
Registered User
Join Date: Apr 2008
Location: Imperial Beach, CA
Posts: 1,040
|
Re: 5k rpm in a few seconds
3500 Dalenzie...
__________________
69 c-10 BBC 462ci, forged crank, H-beam rods, 10.5-1 KB forged pistons, Dart Iron Eagle 308cc, Straub Cam, Comp Cams chrome moly full rollers, Weiand Team G, Prosystems 950, TH400/3500 Dalenzie stall, Currie 9+ Detroit Locker w/31spline axles. 3.5/6in drop. My Build.
|
|
|
|
|
09-15-2011, 10:25 PM
|
#5 |
|
Registered User
Join Date: Feb 2001
Location: Wetumpka, Al, U.S.
Posts: 8,892
|
Re: 5k rpm in a few seconds
I'm not familiar with that brand. Is the truck extremely traction limited?
__________________
Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole! |
|
|
|
|
09-20-2011, 04:15 PM
|
#6 |
|
Registered User
Join Date: Apr 2008
Location: Imperial Beach, CA
Posts: 1,040
|
Re: 5k rpm in a few seconds
They are a local company with a good reputation. It spins a lot down low, if I hammer it from a dead stop then it'll spin for the first 70-100 yards. If I take it light for the first 25 yards it don't spin bad. I do need to soften up the rear end. It has MT drag radials.
Posted via Mobile Device
__________________
69 c-10 BBC 462ci, forged crank, H-beam rods, 10.5-1 KB forged pistons, Dart Iron Eagle 308cc, Straub Cam, Comp Cams chrome moly full rollers, Weiand Team G, Prosystems 950, TH400/3500 Dalenzie stall, Currie 9+ Detroit Locker w/31spline axles. 3.5/6in drop. My Build.
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
