Do I remove this crossmember??? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

J.Cagle · 10-10-2011, 07:12 AM

I am putting a 350 auto in my '64. I know I need to remove the stock crossmember that the original 3 speed manual bolted too, but what about the cross member that all the emergency brake cables bolt too? And, if I remove it, what do I do about e-brake cables?? Thanks, Jared

Wolfinthesnow · 10-10-2011, 09:00 AM

I had a 63 c10 and now I have a 64. My first didn't have the cross member in it when I got it, and I removed the one from my 64. I don't plan on putting it back in. As far as the original goes, I never cared for how the e-brake cables were run. I'm going with an aftermarket setup that runs along side the frame rail. Just my .02
Posted via Mobile Device

jonzcustomshop · 10-10-2011, 10:10 AM

on my 63 it won't fit back around the transmission mount, so I am going to look into using one out of a 66 or later

SuperWho · 10-10-2011, 09:16 PM

Quote:

Originally Posted by Wolfinthesnow

As far as the original goes, I never cared for how the e-brake cables were run. I'm going with an aftermarket setup that runs along side the frame rail. Just my .02
Posted via Mobile Device

Please elaborate, I'm curious on what you are going to use, as I am in your shoes right now.

niterider65 · 10-10-2011, 10:16 PM

heres a couple of pics of what i did I used A crossmember from an 1964 chevy truck I use the automatic cross member and moving the cross member that held the e brake to it was an three speed and i need the mounting space the e brake cross member went i cut the pivot out and the ajuster slide and fabed it to the automactic crossmember. ill get more pics tomarrow nite . here a few might be hard to tell.

niterider65 · 10-11-2011, 08:32 PM

heres the pics of what i did on my auto crossmember .. i cut the mount off the ebrake crossmember and bolted it to my other crossmember .. i used a steal plat and made new new brakets in the stock holes of the crossmember.. and bolted it down i need to hook up the ebrake back togeter after i get the firewall and inside cab done .hope this helps ..

niterider65 · 10-11-2011, 08:40 PM

niterider65 · 10-11-2011, 08:52 PM

and heres the last ones

stsalvage · 10-12-2011, 03:50 AM

you know you can use the ones from a 1964--72 i feel all the 1967--72 still used that set up or gu with the 1973--87 brake cables set up there are tons of them out there

10-10-2011, 07:12 AM	#1
J.Cagle Registered User Join Date: Jun 2011 Location: Dennis Kansas Posts: 335	Do I remove this crossmember??? I am putting a 350 auto in my '64. I know I need to remove the stock crossmember that the original 3 speed manual bolted too, but what about the cross member that all the emergency brake cables bolt too? And, if I remove it, what do I do about e-brake cables?? Thanks, Jared __________________ 1964 c-10 Long stepside, 230 I6 ,3spd, dealer add-on air.

10-10-2011, 09:00 AM	#2
Wolfinthesnow I put the laughter n slaughter Join Date: Feb 2008 Location: Plant City, Fl Posts: 172	Re: Do I remove this crossmember??? I had a 63 c10 and now I have a 64. My first didn't have the cross member in it when I got it, and I removed the one from my 64. I don't plan on putting it back in. As far as the original goes, I never cared for how the e-brake cables were run. I'm going with an aftermarket setup that runs along side the frame rail. Just my .02 Posted via Mobile Device __________________ I still dont care how you did it in California!!!

10-10-2011, 10:10 AM	#3
jonzcustomshop 1961 crewcab Join Date: Dec 2007 Location: missoula, mt Posts: 6,164	Re: Do I remove this crossmember??? on my 63 it won't fit back around the transmission mount, so I am going to look into using one out of a 66 or later __________________ 60 build: http://67-72chevytrucks.com/vboard/s...d.php?t=280904 61 crew build: http://67-72chevytrucks.com/vboard/s...d.php?t=646830 63 build: http://67-72chevytrucks.com/vboard/s...d.php?t=336537 64 'burb build: http://67-72chevytrucks.com/vboard/s...d.php?t=448681 65 'burb build: http://67-72chevytrucks.com/vboard/s...d.php?t=590715 65 build: http://67-72chevytrucks.com/vboard/s...d.php?t=281955

10-10-2011, 10:16 PM	#5
niterider65 Registered User Join Date: Jun 2011 Location: colleyville tx Posts: 623	Re: Do I remove this crossmember??? heres a couple of pics of what i did I used A crossmember from an 1964 chevy truck I use the automatic cross member and moving the cross member that held the e brake to it was an three speed and i need the mounting space the e brake cross member went i cut the pivot out and the ajuster slide and fabed it to the automactic crossmember. ill get more pics tomarrow nite . here a few might be hard to tell. Attached Images

10-11-2011, 08:32 PM	#6
niterider65 Registered User Join Date: Jun 2011 Location: colleyville tx Posts: 623	Re: Do I remove this crossmember??? heres the pics of what i did on my auto crossmember .. i cut the mount off the ebrake crossmember and bolted it to my other crossmember .. i used a steal plat and made new new brakets in the stock holes of the crossmember.. and bolted it down i need to hook up the ebrake back togeter after i get the firewall and inside cab done .hope this helps .. Attached Images

10-11-2011, 08:40 PM	#7
niterider65 Registered User Join Date: Jun 2011 Location: colleyville tx Posts: 623	Re: Do I remove this crossmember??? Attached Images

10-11-2011, 08:52 PM	#8
niterider65 Registered User Join Date: Jun 2011 Location: colleyville tx Posts: 623	Re: Do I remove this crossmember??? and heres the last ones Attached Images

10-12-2011, 03:50 AM	#9
stsalvage Scrapper 1 Join Date: Jan 2007 Location: Riverside Calif Posts: 1,649	Re: Do I remove this crossmember??? you know you can use the ones from a 1964--72 i feel all the 1967--72 still used that set up or gu with the 1973--87 brake cables set up there are tons of them out there



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.