gauge housing - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Phil750 · 11-12-2011, 02:59 PM

I am trying to find a new instrument gauge housing. The screw holes are broke and stripped. This is for 1986 C-20 pickup.
I have been to every site on line with no luck. What are my options if any.
This housing is where the circuit board attaches.http://67-72chevytrucks.com/vboard/i...ilies/waah.gif
Thanks! Phil

**old Rusty C10** · 11-12-2011, 06:37 PM

check out some of the guys in the classifieds parting trucks...

dale3goodwrench · 11-12-2011, 09:10 PM

Post a pic of what exactly you need. I might be able to help you out.

J Knight · 11-12-2011, 11:20 PM

Sounds like you need the white plastic gauge cluster housing to put your gauges and printed curcit on right?

Cramitthefrog · 11-12-2011, 11:26 PM

I have a few also post up what you need, gauges no gauges clock etc.

**hatzie** · 11-13-2011, 11:09 AM

You can probably salvage the housing unless the screw towers are split completely away from the housing.

Carefully drill out the damaged holes till a plastic rod roughly twice the diameter of the screw can barely be inserted with model cement. The sprues from a model car boat etc kit can be used for this. Chuck a short piece in a drill and sand it down to the diameter you need. Cut a little longer than the holes you will be filling.
Set it aside in a warm place till the day after tomorrow. Now that the cement is really dry carefully whittle the patch down to the top of the damaged tower with sand paper.
Re-drill the holes out to pilot diameter for the original screws. Measure the top and bottom of the threads midway up the screw with a dial caliper and pick a drill bit that is roughly halfway between the two diameters (slightly smaller is better than slightly larger).
Carefully screw them back in by hand. Stop and turn backwards at least 1 full turn if it feels too tight. Don't tighten beyond 1/16 of a turn past contact with the gauge faces or you'll strip them again.

11-12-2011, 02:59 PM	#1
Phil750 Registered User Join Date: Dec 2010 Location: Peoria Az Posts: 47	gauge housing I am trying to find a new instrument gauge housing. The screw holes are broke and stripped. This is for 1986 C-20 pickup. I have been to every site on line with no luck. What are my options if any. This housing is where the circuit board attaches.http://67-72chevytrucks.com/vboard/i...ilies/waah.gif Thanks! Phil

11-12-2011, 06:37 PM	#2
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,299	Re: gauge housing check out some of the guys in the classifieds parting trucks... __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!

11-12-2011, 09:10 PM	#3
dale3goodwrench Registered User Join Date: Jan 2008 Location: Cincinnati,ohio Posts: 53	Re: gauge housing Post a pic of what exactly you need. I might be able to help you out.

11-12-2011, 11:20 PM	#4
J Knight Registered User Join Date: Jun 2011 Location: Baytown TX Posts: 2,219	Re: gauge housing Sounds like you need the white plastic gauge cluster housing to put your gauges and printed curcit on right? __________________ John 82 Chevy Silverado 350ci/TH350

11-12-2011, 11:26 PM	#5
Cramitthefrog It's always something Join Date: Jan 2011 Location: Carson City N.V. Posts: 59	Re: gauge housing I have a few also post up what you need, gauges no gauges clock etc.

11-13-2011, 11:09 AM	#6
hatzie Moderator Join Date: Oct 2008 Location: Wentworth, NH Posts: 4,969	Re: gauge housing You can probably salvage the housing unless the screw towers are split completely away from the housing. Carefully drill out the damaged holes till a plastic rod roughly twice the diameter of the screw can barely be inserted with model cement. The sprues from a model car boat etc kit can be used for this. Chuck a short piece in a drill and sand it down to the diameter you need. Cut a little longer than the holes you will be filling. Set it aside in a warm place till the day after tomorrow. Now that the cement is really dry carefully whittle the patch down to the top of the damaged tower with sand paper. Re-drill the holes out to pilot diameter for the original screws. Measure the top and bottom of the threads midway up the screw with a dial caliper and pick a drill bit that is roughly halfway between the two diameters (slightly smaller is better than slightly larger). Carefully screw them back in by hand. Stop and turn backwards at least 1 full turn if it feels too tight. Don't tighten beyond 1/16 of a turn past contact with the gauge faces or you'll strip them again.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.