|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
11-13-2011, 01:06 PM
|
#1 |
|
Registered User
Join Date: Jul 2011
Location: Valley Center, Ca
Posts: 277
|
Am I missing a seat part?
This just dosent look right. A hex seat adjusting nut that sits on a round hole? Looked all over the pLace and cant find a picture of how this seat adjusting screw is supposed to look. Any pictures or referance to a diagram would be appreciated.
|
|
|
|
11-13-2011, 01:46 PM
|
#2 |
|
Registered User
Join Date: Oct 2009
Location: Denton, Texas
Posts: 1,741
|
Re: Am I missing a seat part?
It is kinda hard to tell from your pictures what I am looking at. If it is for the part that leans forward (seat back), then yes - it looks like you should have a couple of nuts
 on it.First 2 pictures, drivers side. 3 picture passenger side. Hope this helps. Keith |
|
|
|
|
11-13-2011, 03:59 PM
|
#3 |
|
Registered User
Join Date: Jul 2011
Location: Valley Center, Ca
Posts: 277
|
Re: Am I missing a seat part?
Posted via Mobile Device
|
|
|
|
|
11-13-2011, 04:04 PM
|
#4 |
|
Registered User
Join Date: Jul 2011
Location: Valley Center, Ca
Posts: 277
|
Re: Am I missing a seat part?
Thats it LiL. Thanks for the pics. Very helpful. Seems like the 2nd nut should be a little larger than the single nut on mine. Or, a washer the size of the surface where the nut sits and a small nut that would go through the hole.
Posted via Mobile Device |
|
|
|
|
11-13-2011, 06:22 PM
|
#5 |
|
Senior Member
 
Join Date: Dec 1999
Location: TN/VA
Posts: 6,389
|
Re: Am I missing a seat part?
You should have a wing nut on the very bottom on both sides
|
|
|
|
|
11-13-2011, 09:04 PM
|
#6 |
|
Registered User
Join Date: Oct 2009
Location: Denton, Texas
Posts: 1,741
|
Re: Am I missing a seat part?
If you have a wing nut on the bottom then the seat back won't lean forward. Mine is a 1968 chevy bench seat.
Keith |
|
|
|
|
11-13-2011, 09:08 PM
|
#7 |
|
Senior Member
Join Date: Dec 1999
Location: TN/VA
Posts: 6,389
|
Re: Am I missing a seat part?
My 67 came with one factory I figure for it to be easy to remove when you needed to get behind your seat and so you want eat the dash as bad if you wreck???
|
|
|
|
|
11-13-2011, 09:11 PM
|
#8 | |
|
Registered User
Join Date: Oct 2009
Location: Denton, Texas
Posts: 1,741
|
Re: Am I missing a seat part?
Quote:
Thanks, I think I will find a wing nut to put on there. My dash does look kinda tasty but I sure wouldn't want to eat it!!  Keith |
|
|
|
|
|
11-13-2011, 09:13 PM
|
#9 |
|
fat old dude
 
Join Date: Feb 2010
Location: fresno, california
Posts: 1,424
|
Re: Am I missing a seat part?
yeah a wing nut to prevent the 67-68 seats from flying forward when u get to a stop
__________________
1972 c-10 shortbed 350/400 build thread http://67-72chevytrucks.com/vboard/s...d.php?t=389157 1968 workhorse http://67-72chevytrucks.com/vboard/s...d.php?t=446216 Accepting part donations |
|
|
|
|
11-13-2011, 09:15 PM
|
#10 |
|
Senior Member
Join Date: Dec 1999
Location: TN/VA
Posts: 6,389
|
Re: Am I missing a seat part?
Hey Keith, My 67 came from my Great Uncle whom bought it new but I did remove the passenger side one so if I needed behind the seat I would just have to remove the one on my side and not walk around the truck.
|
|
|
|
|
11-13-2011, 09:25 PM
|
#11 |
|
Registered User
Join Date: Oct 2009
Location: Denton, Texas
Posts: 1,741
|
Re: Am I missing a seat part?
Thanks to Tim Christian, Heeroyue2002, and Arl37, I learned something new today. Yeah I would have been in for a rude surprise if I got into a fender bender and the seat goes flying forward. I still only have the lap belts too!
 Thank you! Keith |
|
|
|
|
11-14-2011, 09:33 PM
|
#12 |
|
Registered User
Join Date: Jul 2011
Location: Valley Center, Ca
Posts: 277
|
Re: Am I missing a seat part?
thanks everyone for your help
Posted via Mobile Device |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
