CA Parting 68 GMC 2500 2wd - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

klieber · 02-10-2012, 12:09 AM

Quote:

Originally Posted by KrazyRay

klieber...The belts are in good driver condition, the female ends are nice. $32 total shipped. I will pst pics tomorrow.

OK, I'll take them pending pictures.

KrazyRay · 02-10-2012, 09:32 PM

The seat belts look clean. There is a scuff on one retractor housing, they could use some lube on the return spring, and the date labels are wore. Overall, a good daily driver set.
This right inner is one of the cleanest I have come across...very solid. A little bit of wire wheeling at the bottom and good to go.
The fender cup is one of the most solid ones I've seen, but there is a couple of dents that look easy to deal with.

Meatman · 02-11-2012, 01:11 AM

No rust issues or crud buildup on inside of fender cup? Mine rusted from inside out due to dirt buildup.

KrazyRay · 02-11-2012, 01:17 AM

No crud on the inside. I can get close ups Sun.
Thanks,
Ray

Meatman · 02-11-2012, 01:40 AM

Ya that would be great. Might mark where your gonna cut it too if you would. Just want to make sure its not same condition as mine now. Thanks

shaneschevys · 02-11-2012, 02:45 AM

How much for the door panels? just need the vinyl covers if possible.

KrazyRay · 02-11-2012, 05:54 PM

Quote:

Originally Posted by shaneschevys

How much for the door panels? just need the vinyl covers if possible.

I can do $40 shipped to TX. for the 2 door panels. The driver side has some wrinkles, but you might be able to work out.
Thanks,
Ray

shaneschevys · 02-11-2012, 06:15 PM

I will take them. I can paypal or money order which ever you would like.

KrazyRay · 02-11-2012, 11:57 PM

pm sent to Shane
The fender cup is very clean on the inside.
The rear of the fender lower patch is available for $20 plus shipping...super clean.
Thanks,
Ray

Meatman · 02-12-2012, 01:14 AM

Ill take cup and the lone hub cap!

jlive68 · 02-12-2012, 10:22 PM

you wouldn't have the clip that goes from the carb rod to the accelerator rod do you.... I need one bad

KrazyRay · 02-13-2012, 12:06 AM

Probably not, but I will check.

KrazyRay · 02-13-2012, 09:29 PM

pics for Shane

shaneschevys · 02-13-2012, 10:18 PM

They look good! I will take them. Pm sent
Posted via Mobile Device

tooter · 02-15-2012, 07:22 PM

Got them today Thanks

KrazyRay · 02-16-2012, 08:44 PM

Antenna pics for Fred

CC69Rat · 02-24-2012, 07:56 PM

Ray - Post #47 I'll take the wheel tubs. PM and Payment sent

villa 66 · 03-01-2012, 10:08 PM

Is it disk brake? What would u take for both spindels,rotors,calipers shipped too Tx. 78570? If possible pics.

KrazyRay · 03-01-2012, 10:45 PM

Sorry, its drum brakes. Try to find one local as shipping is brutal on these parts.
Thanks,
Ray

02-10-2012, 09:32 PM	#52
KrazyRay Registered User Join Date: Jun 2009 Location: Oroville, CA Posts: 4,827	Re: Parting 68 GMC 2500 2wd The seat belts look clean. There is a scuff on one retractor housing, they could use some lube on the return spring, and the date labels are wore. Overall, a good daily driver set. This right inner is one of the cleanest I have come across...very solid. A little bit of wire wheeling at the bottom and good to go. The fender cup is one of the most solid ones I've seen, but there is a couple of dents that look easy to deal with. Attached Images

02-11-2012, 01:11 AM	#53
Meatman Registered User Join Date: Sep 2004 Location: Topeka, Ks Posts: 604	Re: Parting 68 GMC 2500 2wd No rust issues or crud buildup on inside of fender cup? Mine rusted from inside out due to dirt buildup. __________________ Daily-94 K2500 350 5spd extended cab longbox Project Red Velvet-68 C20 396-th400-AC-PS-PB-all original except for the 8 track and the gun rack. Build thread>>>>http://67-72chevytrucks.com/vboard/s...d.php?t=495881 My 01 TA and 88 Formula hide in the garage. :-)

02-11-2012, 01:17 AM	#54
KrazyRay Registered User Join Date: Jun 2009 Location: Oroville, CA Posts: 4,827	Re: Parting 68 GMC 2500 2wd No crud on the inside. I can get close ups Sun. Thanks, Ray

02-11-2012, 01:40 AM	#55
Meatman Registered User Join Date: Sep 2004 Location: Topeka, Ks Posts: 604	Re: Parting 68 GMC 2500 2wd Ya that would be great. Might mark where your gonna cut it too if you would. Just want to make sure its not same condition as mine now. Thanks __________________ Daily-94 K2500 350 5spd extended cab longbox Project Red Velvet-68 C20 396-th400-AC-PS-PB-all original except for the 8 track and the gun rack. Build thread>>>>http://67-72chevytrucks.com/vboard/s...d.php?t=495881 My 01 TA and 88 Formula hide in the garage. :-)

02-11-2012, 02:45 AM	#56
shaneschevys Its always something! Join Date: Aug 2005 Location: FT Worth,TX Posts: 4,992	Re: Parting 68 GMC 2500 2wd How much for the door panels? just need the vinyl covers if possible. __________________ 79 p10 stepvan 72 Short Fleetside 72 Suburban 67 GMC One Ton Flatbed 64 Short Fleetside 57 Chevy 2DR Hard Top 57 Chevy 2dr wagon 65 f* short fleet 63 C 60 Flatbed Member of the patina club**

02-11-2012, 06:15 PM	#58
shaneschevys Its always something! Join Date: Aug 2005 Location: FT Worth,TX Posts: 4,992	Re: Parting 68 GMC 2500 2wd I will take them. I can paypal or money order which ever you would like. __________________ 79 p10 stepvan 72 Short Fleetside 72 Suburban 67 GMC One Ton Flatbed 64 Short Fleetside 57 Chevy 2DR Hard Top 57 Chevy 2dr wagon 65 f* short fleet 63 C 60 Flatbed Member of the patina club**

02-11-2012, 11:57 PM	#59
KrazyRay Registered User Join Date: Jun 2009 Location: Oroville, CA Posts: 4,827	Re: Parting 68 GMC 2500 2wd pm sent to Shane The fender cup is very clean on the inside. The rear of the fender lower patch is available for $20 plus shipping...super clean. Thanks, Ray Attached Images

02-12-2012, 01:14 AM	#60
Meatman Registered User Join Date: Sep 2004 Location: Topeka, Ks Posts: 604	Re: Parting 68 GMC 2500 2wd Ill take cup and the lone hub cap! __________________ Daily-94 K2500 350 5spd extended cab longbox Project Red Velvet-68 C20 396-th400-AC-PS-PB-all original except for the 8 track and the gun rack. Build thread>>>>http://67-72chevytrucks.com/vboard/s...d.php?t=495881 My 01 TA and 88 Formula hide in the garage. :-) Last edited by Meatman; 02-12-2012 at 10:55 AM.

02-12-2012, 10:22 PM	#61
jlive68 Senior Member Join Date: Apr 2004 Location: Greenville, Tx. Posts: 286	Re: Parting 68 GMC 2500 2wd you wouldn't have the clip that goes from the carb rod to the accelerator rod do you.... I need one bad __________________ 1968 chevy U.S. Navy

02-13-2012, 12:06 AM	#62
KrazyRay Registered User Join Date: Jun 2009 Location: Oroville, CA Posts: 4,827	Re: Parting 68 GMC 2500 2wd Probably not, but I will check.

02-13-2012, 09:29 PM	#63
KrazyRay Registered User Join Date: Jun 2009 Location: Oroville, CA Posts: 4,827	Re: Parting 68 GMC 2500 2wd pics for Shane Attached Images

02-13-2012, 10:18 PM	#64
shaneschevys Its always something! Join Date: Aug 2005 Location: FT Worth,TX Posts: 4,992	Re: Parting 68 GMC 2500 2wd They look good! I will take them. Pm sent Posted via Mobile Device __________________ 79 p10 stepvan 72 Short Fleetside 72 Suburban 67 GMC One Ton Flatbed 64 Short Fleetside 57 Chevy 2DR Hard Top 57 Chevy 2dr wagon 65 f* short fleet 63 C 60 Flatbed Member of the patina club**

02-15-2012, 07:22 PM	#65
tooter Registered User Join Date: Dec 2010 Location: Moss Point , Ms Posts: 1,342	Re: Parting 68 GMC 2500 2wd Got them today Thanks __________________ My Ole 67 http://67-72chevytrucks.com/vboard/s...d.php?t=505830

02-16-2012, 08:44 PM	#66
KrazyRay Registered User Join Date: Jun 2009 Location: Oroville, CA Posts: 4,827	Re: Parting 68 GMC 2500 2wd Antenna pics for Fred Attached Images

02-24-2012, 07:56 PM	#67
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,212	Re: Parting 68 GMC 2500 2wd Ray - Post #47 I'll take the wheel tubs. PM and Payment sent __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)



Register or Log In To remove these advertisements.

03-01-2012, 10:08 PM	#68
villa 66 Registered User Join Date: May 2009 Location: MERCEDES,TEXAS Posts: 146	Re: Parting 68 GMC 2500 2wd Is it disk brake? What would u take for both spindels,rotors,calipers shipped too Tx. 78570? If possible pics.

03-01-2012, 10:45 PM	#69
KrazyRay Registered User Join Date: Jun 2009 Location: Oroville, CA Posts: 4,827	Re: Parting 68 GMC 2500 2wd Sorry, its drum brakes. Try to find one local as shipping is brutal on these parts. Thanks, Ray

Register or Log In To remove these advertisements.