Does any one have this? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

dgreen · 04-25-2012, 03:33 PM

Just what it says, http://www.performanceonline.com/197...-KIT-FRK7387P/
If so pros cons , looking to over hall my Suspension. and also sell Tubular Control Arm for 80-87?

INSIDIOUS '86 · 04-25-2012, 08:15 PM

Pros: cheap.
Cons: no control arm bushing outer sleeve.
Cheap. Not name brand parts.

I'm song a full suspension rebuild on mine

With this kit you should also get the idler arm an pitman arm
Posted via Mobile Device

dgreen · 04-26-2012, 07:08 AM

Should i just get all mogg front end parts would that be better?

INSIDIOUS '86 · 04-27-2012, 02:06 AM

Quote:

Originally Posted by dgreen

Should i just get all moog front end parts would that be better?

It will be about 471.45 with all moog and urethane bushings from energy suspension

Don't forget the cost of grease and labor for having your bushings and ball joints pressed.

http://www.summitracing.com/parts/MOG-K6247T/
http://www.summitracing.com/parts/MOG-K6143/

http://www.summitracing.com/parts/MOG-K6136/
http://www.summitracing.com/parts/MOG-ES409RT/
http://www.summitracing.com/parts/MOG-ES409LT/
http://www.summitracing.com/parts/ENS-3-3161G/

You need two inner and two outer tie rods, and two upper and two Lower ball joints

Total cost is $471.45
Posted via Mobile Device

INSIDIOUS '86 · 04-27-2012, 02:11 AM

After this go with a one tone away bar up front with urethan middle bushings and stock side rubbers

Don't worry about bump stops or adjusting sleeves. More than likely the stock ones are just fine
Posted via Mobile Device

dgreen · 04-27-2012, 06:17 AM

awesome going to get all the moog parts in about 2 weeks ! thannks

andrewmp6 · 04-28-2012, 02:01 AM

I only use moog parts to me there ball joints last longer then other off brands i have tried before.

InLimbo · 05-04-2012, 04:22 PM

What INSIDIOUS 86 said, but go through Rockauto. Same parts 25-45% cheaper and if you google "rockauto coupon" you can find a code for another 5% off! I am looking to do my suspension soon too, here are part #s of what I have compiled so far. Not all inclusive I am sure. All #s are moog/timken parts.
My truck is an 85 if it makes a difference.

Upper ball joints K6136
Lower ball joints K6117T
Upper arm bushings x2 K6138
Lower arm bushings x2 K6137
Idler arm K6247T
Pitman arm K6143
Tie rod ends ES409RT x2 ES409LT X2
Tie rod adjusters ES2004S x2
Wheel bearings outer x2 SET3
Wheel bearings inner x2 SET6
Bearing seals x2 8871

Please feel free to add to this, I may have forgotten something. I only want to tear it apart once!

04-25-2012, 03:33 PM	#1
dgreen Registered User Join Date: May 2011 Location: rochester ny Posts: 176	Does any one have this? Just what it says, http://www.performanceonline.com/197...-KIT-FRK7387P/ If so pros cons , looking to over hall my Suspension. and also sell Tubular Control Arm for 80-87?

04-25-2012, 08:15 PM	#2
INSIDIOUS '86 Registered User Join Date: Jul 2009 Location: washington Posts: 4,178	Re: Does any one have this? Pros: cheap. Cons: no control arm bushing outer sleeve. Cheap. Not name brand parts. I'm song a full suspension rebuild on mine With this kit you should also get the idler arm an pitman arm Posted via Mobile Device __________________ 377 sbc thumpr cam autogear m23 muncie 3:73 Detroit trutrac 3''spintech prostreet mufflers xpipe 1 3/4 headers build thread !http://67-72chevytrucks.com/vboard/s...d.php?t=577217 Iroc gauge threadhttp://67-72chevytrucks.com/vboard/s...d.php?t=554511

04-26-2012, 07:08 AM	#3
dgreen Registered User Join Date: May 2011 Location: rochester ny Posts: 176	Re: Does any one have this? Should i just get all mogg front end parts would that be better?

04-27-2012, 02:11 AM	#5
INSIDIOUS '86 Registered User Join Date: Jul 2009 Location: washington Posts: 4,178	Re: Does any one have this? After this go with a one tone away bar up front with urethan middle bushings and stock side rubbers Don't worry about bump stops or adjusting sleeves. More than likely the stock ones are just fine Posted via Mobile Device __________________ 377 sbc thumpr cam autogear m23 muncie 3:73 Detroit trutrac 3''spintech prostreet mufflers xpipe 1 3/4 headers build thread !http://67-72chevytrucks.com/vboard/s...d.php?t=577217 Iroc gauge threadhttp://67-72chevytrucks.com/vboard/s...d.php?t=554511

04-27-2012, 06:17 AM	#6
dgreen Registered User Join Date: May 2011 Location: rochester ny Posts: 176	Re: Does any one have this? awesome going to get all the moog parts in about 2 weeks ! thannks

04-28-2012, 02:01 AM	#7
andrewmp6 Registered User Join Date: Jan 2009 Location: Louisville,Ky Posts: 5,811	Re: Does any one have this? I only use moog parts to me there ball joints last longer then other off brands i have tried before.

05-04-2012, 04:22 PM	#8
InLimbo Registered User Join Date: Oct 2010 Location: Charleston, SC Posts: 34	Re: Does any one have this? What INSIDIOUS 86 said, but go through Rockauto. Same parts 25-45% cheaper and if you google "rockauto coupon" you can find a code for another 5% off! I am looking to do my suspension soon too, here are part #s of what I have compiled so far. Not all inclusive I am sure. All #s are moog/timken parts. My truck is an 85 if it makes a difference. Upper ball joints K6136 Lower ball joints K6117T Upper arm bushings x2 K6138 Lower arm bushings x2 K6137 Idler arm K6247T Pitman arm K6143 Tie rod ends ES409RT x2 ES409LT X2 Tie rod adjusters ES2004S x2 Wheel bearings outer x2 SET3 Wheel bearings inner x2 SET6 Bearing seals x2 8871 Please feel free to add to this, I may have forgotten something. I only want to tear it apart once!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.