07-06-2012, 04:03 PM | #1 |
Registered User
Join Date: Jun 2012
Location: Oregon City, OR
Posts: 49
|
Airbag help needed
Hey guys. I just bought a 66 C20 Fleetside. The suspension in this thing is so bad I swear it is the factory shocks and springs. It is dangerous to drive on the freeway and is basically useless as a truck.
I have over the years learned many lessons when it comes to lowering/lifted vehicles. You can never go too high or too low. With that said, I have wasted a ton of money on suspensions only to end up replacing it later to go higher or lower. And sometimes maybe even again. I am trying to plan out this truck a little better. I want to be sure that each stage in this project will get me to where I ultimately want to be. That goal is to one day be bagged and laying the frame. Now, my next stage in this project is to do something with the suspension. I have to make it safe and useable. I would like to buy bags for the front and rear as well as a cheap set of shocks (disposable). Once the bags are installed it would basically be used at roughly stock height until I am ready to tackled the front spindles and notching the frame. So I am looking for bags that will work for now at a stock height but can ultimately lay frame down the road. I came across this link that basically looks like what I will want to do to start. http://67-72chevytrucks.com/vboard/s...d.php?t=129463 After looking through that post I came across this kit at ***************** for the front. You can get the airlift or slam bags with it. http://*************/-63-87-fullsize-...ag-bracket-kit. I don't know the difference between the bags and/or compressors, etc. Can you guys help me figure out what I am looking for? Kits? Brands? Obviously looking for the best value for my $$$. I am new to bags/air management systems and really would like to know what to look for and what to stay away from. Thanks for your advice! Shawn
__________________
1966 C20 Long Bed Fleetside 1988 Jeep YJ Hybrid Monster |
07-06-2012, 04:20 PM | #2 |
Registered User
Join Date: May 2005
Location: Beaverton, OR
Posts: 3,728
|
Re: Airbag help needed
That is one of the best write ups on this site and is exactly what I used when I bagged my '69. You can get everything you need from a site vendor here. Check out the suspension marketplace and poke around the suspension forum.
One of the vendors posted an air management kit with manual valves for under $600. Add some brackets, and 4 bags, you are set. Welcome to the forum.
__________________
New Project: 1966 LWB C20 Plans: 1/2 ton conversion Dropmember front Dropmember rear Corvette discs Restored raised bed http://67-72chevytrucks.com/vboard/s....php?p=4295210 |
07-06-2012, 04:21 PM | #3 |
Registered User
Join Date: May 2005
Location: Beaverton, OR
Posts: 3,728
|
Re: Airbag help needed
__________________
New Project: 1966 LWB C20 Plans: 1/2 ton conversion Dropmember front Dropmember rear Corvette discs Restored raised bed http://67-72chevytrucks.com/vboard/s....php?p=4295210 |
07-13-2012, 01:46 PM | #4 |
Registered User
Join Date: Jun 2012
Location: Oregon City, OR
Posts: 49
|
Re: Airbag help needed
Thanks jimmydean for the info. I found this post http://67-72chevytrucks.com/vboard/s...d.php?t=442745 on the marketplace. Would these be a good choice? I emailed him but never got a reply back.
I read in another post that someone had better luck/ride with the 2500 bags over the 2600 bags. I am wanting the best ride as well as the ability to haul and lower if needed. Thanks again!
__________________
1966 C20 Long Bed Fleetside 1988 Jeep YJ Hybrid Monster |
Bookmarks |
|
|