Swapping cabs - The 1947 - Present Chevrolet & GMC Truck Message Board Network

smallbigblock · 10-01-2003, 10:36 PM

Has anyone here put a cab from a 1-ton chassis on a half ton? Is it a direct swap or are the mounts different? I have a chance to get a 1-ton cheap that has a nice cab that I need for my truck. If anyone has done this let me know. I don't want to buy something that I can't use.

Longhorn Man · 10-01-2003, 10:54 PM

The cab itsself is the exact same as a 1/2 ton, however, if your 1/2 ton is a 2 wheel drive, the cab mounts are not the same. (cab mounts as in the rubber piece...not the metal on the bottom of the cab)

O'l Buck · 10-02-2003, 01:37 AM

The only thing I can think of is you may have to swap tranny humps, no big deal, they just bolt in. The 1 ton will probably be a high hump, and your 1/2 ton is probably a low hump. Unless it's a 4x4, then it will be the high hump.

Longhorn Man · 10-04-2003, 12:12 AM

The one ton follows the same rules as the lighter trucks do as for the hump size.
Big hump is on 4 speed trucks, big block trucks and 4X4 trucks...all others are small hump. (note that they did not make a 4X4 one ton)

jcueckert13 · 10-04-2003, 08:42 AM

what parts would it take to upgrade a 3/4 ton 4x4 to a 1 ton 4x4

Longhorn Man · 10-05-2003, 01:33 PM

rear axle, and springs. If you have coil, then you need to go to leaf.
Even then, it would have a 3/4 ton frame. So a fram is needed too in reality, but then your bed wouldn't fit, so you need a longhorn bed too.

Tx Firefighter · 10-05-2003, 02:56 PM

Longhorn man, don't the 1 tons have cab lights? Seems like they all do to me. Would look unusual on a 1/2 ton.

Longhorn Man · 10-05-2003, 06:59 PM

No, they do not all have clearance lights. It was an option. However, I think the cab chassis version (which would be most of the one tons sold) were required to have them...I'd have to look at the books.
But it was an option on the one ton fleet (longhorn) and the one ton step (9 foot bed) rucks.
Clearance lights were an option on 1/2 ton trucks. I was looking at a 71 cheeyene in the junk yard the other day with them on there.

Tx Firefighter · 10-05-2003, 07:11 PM

The trucks with cab lights, they have little raised areas on the roof don't they? What I mean is, the roof panel itself is actually different than non light trucks, it's more than just holes.

Down here in Texas, I've never even seen a C30 that isn't a dually. They must be pretty uncommon.

I see long steps everywhere. I know of about 5 sitting abandoned that I'm sure could be picked up real cheap. They are all C10s though. And, come to think of it, all 69-70s too.

Kevin

Longhorn Man · 10-05-2003, 09:02 PM

All the long steps you are seeing are the normal 8 foot bed, the one ton steps are 9 foot.
You've probably seen non daulie one tons and didn't realize it.
Although, i wonder what the production numbers would be for daulie verses single tire axles. Hmmm...

72MARIO · 10-05-2003, 09:35 PM

Longhorn Man'

You are the master !

Longhorn Man · 10-05-2003, 11:27 PM

naaa, just know too much about stuff that don't help pay the bills.

10-01-2003, 10:36 PM	#1
smallbigblock Registered User Join Date: Jan 2001 Location: Malden, Missouri, USA Posts: 109	Swapping cabs Has anyone here put a cab from a 1-ton chassis on a half ton? Is it a direct swap or are the mounts different? I have a chance to get a 1-ton cheap that has a nice cab that I need for my truck. If anyone has done this let me know. I don't want to buy something that I can't use. __________________ 72 Cheyenne Super LWB 72 C-10 Short Stepside 71 Nova

10-02-2003, 01:37 AM	#3
O'l Buck Recovering Truck Driver Join Date: Mar 2002 Location: Orleans, NE USA Posts: 1,883	The only thing I can think of is you may have to swap tranny humps, no big deal, they just bolt in. The 1 ton will probably be a high hump, and your 1/2 ton is probably a low hump. Unless it's a 4x4, then it will be the high hump. __________________ 67 K-20 350, SM465, Eaton rear, 4.56 no spin option 00 Dodge 2500 4x4, 24V cummins, 5 speed Chad South Central Nebraska

10-04-2003, 08:42 AM	#5
jcueckert13 Registered User Join Date: Apr 2003 Location: Edgewood New Mexico Posts: 2,088	what parts would it take to upgrade a 3/4 ton 4x4 to a 1 ton 4x4 __________________ 1990 subaru legcy (daily driver) 1987 Toyota 4runner (weekend toy) 1968 C30 flatbed dually 1970 C10 longbed stepside (in pieces) 1976 Dodge Dart 1963 Dodge Dart

10-05-2003, 02:56 PM	#7
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Longhorn man, don't the 1 tons have cab lights? Seems like they all do to me. Would look unusual on a 1/2 ton. __________________ I'm on the Instagram- @Gearhead_Kevin

10-05-2003, 07:11 PM	#9
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	The trucks with cab lights, they have little raised areas on the roof don't they? What I mean is, the roof panel itself is actually different than non light trucks, it's more than just holes. Down here in Texas, I've never even seen a C30 that isn't a dually. They must be pretty uncommon. I see long steps everywhere. I know of about 5 sitting abandoned that I'm sure could be picked up real cheap. They are all C10s though. And, come to think of it, all 69-70s too. Kevin __________________ I'm on the Instagram- @Gearhead_Kevin

10-01-2003, 10:54 PM	#2
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	The cab itsself is the exact same as a 1/2 ton, however, if your 1/2 ton is a 2 wheel drive, the cab mounts are not the same. (cab mounts as in the rubber piece...not the metal on the bottom of the cab)

10-04-2003, 12:12 AM	#4
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	The one ton follows the same rules as the lighter trucks do as for the hump size. Big hump is on 4 speed trucks, big block trucks and 4X4 trucks...all others are small hump. (note that they did not make a 4X4 one ton)

10-05-2003, 01:33 PM	#6
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	rear axle, and springs. If you have coil, then you need to go to leaf. Even then, it would have a 3/4 ton frame. So a fram is needed too in reality, but then your bed wouldn't fit, so you need a longhorn bed too.

10-05-2003, 06:59 PM	#8
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	No, they do not all have clearance lights. It was an option. However, I think the cab chassis version (which would be most of the one tons sold) were required to have them...I'd have to look at the books. But it was an option on the one ton fleet (longhorn) and the one ton step (9 foot bed) rucks. Clearance lights were an option on 1/2 ton trucks. I was looking at a 71 cheeyene in the junk yard the other day with them on there.

10-05-2003, 09:02 PM	#10
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	All the long steps you are seeing are the normal 8 foot bed, the one ton steps are 9 foot. You've probably seen non daulie one tons and didn't realize it. Although, i wonder what the production numbers would be for daulie verses single tire axles. Hmmm...

10-05-2003, 09:35 PM	#11
72MARIO Registered User Join Date: Nov 2000 Location: Huntsville Ontario Canada Posts: 4,052	Longhorn Man' You are the master ! __________________ 1968 Suburban numbers matching all original truck now equipped with 6.0/4L80 on Accuair http://67-72chevytrucks.com/vboard/s...d.php?t=625017 1967 C/20 6.0/4L80 Roofing Truck 1990 V2500 Suburban "Plow Truck" 2005 TAHOE DD

10-05-2003, 11:27 PM	#12
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	naaa, just know too much about stuff that don't help pay the bills.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.