The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 08-20-2012, 03:20 PM   #1
Eyegore
What Hump?
 
Eyegore's Avatar
 
Join Date: Apr 2003
Location: New River AZ
Posts: 2,009
Changing main seals while engine still in blazer

Help my sons 78 k5 appears to need the main seals replaced, has anyone done it while it was still in the truck? Its a k5 with a 8" lift 400 cid engine.
__________________
Lil red 86 c-10
99 Sub
78 Camper Special w/ 454
Eyegore is offline   Reply With Quote
Old 08-21-2012, 09:05 AM   #2
manimal
Registered User
 
manimal's Avatar
 
Join Date: Oct 2006
Location: Southern Kalifornia
Posts: 3,066
Re: Changing main seals while engine still in blazer

Since it has a lift the it shouldt be too hard. Drop pan,unbolt rear main cap. With an awl or small flat screwdriver,push the old main seal out,being careful not to touch the crank. Then push the new one in place(block side) and replace the main cap side. The re-install main cap(use some assembly lube on bearing) and torque to spec. Get a Felpro 1pc oil pan gasket,will make life WAY EASIER!
ALSO put a light coat of oil on the seal lip so it doesnt run dry.
__________________
------------------------------------------------------
-Lance
2000 Chevy C2500, 5.7, 4L80e
1999 Suburban K2500, 7.4, 4L80e
1980 Camaro..son's car...PROJECT
manimal is offline   Reply With Quote
Old 08-21-2012, 09:15 AM   #3
gchemist
BAD BOW-Silverado XST
 
gchemist's Avatar
 
Join Date: May 2000
Location: Senior Member from Austin, TX
Posts: 6,431
Re: Changing main seals while engine still in blazer

Follow these instructions: http://www.73-87.com/7387garage/drivetrain/rearseal.htm
__________________
Gerardo a.k.a. Mad Chemist
Silverado XST videos
gchemist is offline   Reply With Quote
Old 08-21-2012, 08:22 PM   #4
DetroitIron
Registered User
 
DetroitIron's Avatar
 
Join Date: Jul 2010
Location: Hudsonville, MI
Posts: 174
Re: Changing main seals while engine still in blazer

Quote:
Originally Posted by manimal View Post
Since it has a lift the it shouldt be too hard. Drop pan,unbolt rear main cap. With an awl or small flat screwdriver,push the old main seal out,being careful not to touch the crank. Then push the new one in place(block side) and replace the main cap side. The re-install main cap(use some assembly lube on bearing) and torque to spec. Get a Felpro 1pc oil pan gasket,will make life WAY EASIER!
ALSO put a light coat of oil on the seal lip so it doesnt run dry.
With the transmission removed or can this be done without removing trans?
__________________
_______________________________________________

1985 Chevy Scottsdale K20 350 with 700R4 running 3.42 gearing aka "The Honey Badger"
1993 Silverado C3500 Ext. Cab Dually 6.5 turbo diesel
DetroitIron is offline   Reply With Quote
Old 08-21-2012, 08:26 PM   #5
mud.man.rj
Registered User
 
mud.man.rj's Avatar
 
Join Date: Dec 2011
Location: Creighton Sask. Canada
Posts: 4,121
Re: Changing main seals while engine still in blazer

Just pull the inspection plate from trans then do as stated earilier, no big deal, don't do it hot let the oil drip down into the pan for awhile not right after running it that way it isn't drip drip dripping off the crank on your face. Just did one and a HV oil pump too.
mud.man.rj is offline   Reply With Quote
Old 08-25-2012, 12:59 AM   #6
Eyegore
What Hump?
 
Eyegore's Avatar
 
Join Date: Apr 2003
Location: New River AZ
Posts: 2,009
Re: Changing main seals while engine still in blazer

Thanks everyone, he is ging to try it next week. Thanks again!!
__________________
Lil red 86 c-10
99 Sub
78 Camper Special w/ 454
Eyegore is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:05 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com