|
12-08-2012, 03:19 PM
|
#1 |
|
Registered User
Join Date: Jul 2010
Location: Hemet,Ca
Posts: 1,502
|
Pinion bolt
I have a 67 chevy c10 lwb with original rear end. Do not know gear ratio. But anyways I notice a leak from the pinion area. So I removed the driveshaft and am tryin to get the Pinion Bolt off but it won't budge. I am using a 1 1/8 socket with the airgun and nothing is turning. PUt alot of wd40 since Weds. I am trying to replace the Crush sleeve. I believe that is causing the leak. Any help and all is welcome. Its kickin my butt.
__________________
Stovebolt-It is painted |
|
|
|
12-08-2012, 04:22 PM
|
#2 |
|
Registered User
Join Date: Jun 2010
Location: Upland Ca
Posts: 4,141
|
Re: Pinion bolt
Most home compressors and impact guns don't have enough power to get that nut off. You'll need to get the wheels on it and on the ground, block them good, use a breaker bar (a piece of pipe on the breaker bar or ratchet) at least 1/2 drive. The crush sleeve will not cause it to leak. I'd just replace the seal, clean up the area real good, apply a little silicon sealer to the metal lip. Make sure you lube up the rubber seal to.
__________________
1972 C10 SWB, Air, PS, PB, 350/350THM. Second owner. 1965 Corvette roadster, 44K miles, 327/365 SHP, 4 speed, side exhaust, knockoffs, teak, second owner (bought in 1970), Have ALL numbers matching components. My frame off restoration thread: http://67-72chevytrucks.com/vboard/s...d.php?t=556703 |
|
|
|
|
12-08-2012, 04:31 PM
|
#3 |
|
Registered User
Join Date: Jul 2010
Location: Hemet,Ca
Posts: 1,502
|
Re: Pinion bolt
Yep that sounds like a plan right there. Thank you!
__________________
Stovebolt-It is painted |
|
|
|
|
12-08-2012, 11:05 PM
|
#4 |
|
Registered User
Join Date: Jan 2012
Location: Glencoe Alabama
Posts: 510
|
Re: Pinion bolt
Personally, I would use a new nut when i go back together. Be sure and not overtighten going back together, it is easy to do and you'll wear the bearing out. It really just has to be snug. Something like 15 inch ilbs of pressure to turn pinion and that ain't much. Tighten like a wheel bearing if that helps.
__________________
72 Cheyenne super 10 08 3500 HD 4dr dually 12 ford flex (wifes ride) 76 Monte Carlo 83 Chevy short wide Silverado 96 Mazda Miata, 2000 Allegro Bus |
|
|
|
|
12-09-2012, 12:19 AM
|
#5 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,403
|
Re: Pinion bolt
Yup, 15 inches of rotating tork....new bearings, maybe a tick more. But right on line with what the 1st good man had to say
 crazyL
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
12-09-2012, 01:25 AM
|
#6 |
|
18 Till I Die
Join Date: Mar 2005
Location: Alberta, Canada
Posts: 1,522
|
Re: Pinion bolt
You can't do rotating torque spec with the diff all assembled. Mark the nut to the pinion and yolk with a center punch. Using a breakerbar remove nut if your impact wont do it. Tap yolk off and replace seal. You might need a speedy sleeve if there are some serious grooves in the yolk. Reassemble with marks lining up and reinstall nut. Tighten till all marks line up then go a little past to get pressure on the crush sleeve again.
__________________
2011 GMC Acadia 1969 GMC BBC LS7 2007 GMC Crew Duramax 1987 Camaro Iroc 350 Tuned Port Injection 42000Km 1987 Chevrolet Silverado 350 TBI 1987 Chevrolet Silverado 350 TBI(yes 2) Take me drunk, I'm too home... 
|
|
|
|
|
12-09-2012, 02:31 AM
|
#7 | |
|
Moderator
 
Join Date: May 2007
Location: Southern Cal
Posts: 19,995
|
Re: Pinion bolt
Quote:
Posted via Mobile Device
__________________
1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man |
|
|
|
|
|
12-09-2012, 11:13 PM
|
#8 |
|
Registered User
Join Date: Jan 2012
Location: Glencoe Alabama
Posts: 510
|
Re: Pinion bolt
You can do rotating torque if you are careful. Back the pinion up to where it isn't engaged to the ring gear (you can feel it) It will only move forward maybe a 1/2 inch before it contacts the ring gear again but enough to measure the torque it took to move it without trying to move ring gear too.
__________________
72 Cheyenne super 10 08 3500 HD 4dr dually 12 ford flex (wifes ride) 76 Monte Carlo 83 Chevy short wide Silverado 96 Mazda Miata, 2000 Allegro Bus |
|
|
|
|
12-09-2012, 11:52 PM
|
#9 |
|
Registered User
 
Join Date: May 2012
Location: Anton, Texas
Posts: 2,364
|
Re: Pinion bolt
be sure and put in new rear end grease when you are done, it needs to be replaced every now and then.
|
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
