Fender Question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

FloatMonkey · 12-10-2012, 03:13 AM

So I got my 1970 GMC truck back from the body shop and the right front GMC V-8 1500 emblem was on crooked and the front chrome eyebrow piece does not fit correctly either. I know there is a differece between the Chevrolet and GMC fenders, what are those differences?
Posted via Mobile Device
Posted via Mobile Device

hugger6933 · 12-10-2012, 08:21 AM

The differences would not effect your problems. The boy lines at the front of the GMC are different like a 68 Chevy around the front grille opening where the moulding attaches. Most likely it they have installed a new fender, the holes are not there if I remember correctly. So they had to have drilled them at them shop, or they[the holes] were there and the stamper put them in crooked and that idea is not far fetched either. Jim

**RenoKeene** · 12-10-2012, 12:08 PM

The fender emblem is a quick fix, elongate the stud holes a little. The emblem should hide the holes. As far as the eyebrow goes if it is a repop it probably won't fit worth a dam as the stamping is junk. Loosen the nuts inside the fender and move it around until your happy. I spent several hours getting mine where I wanted them to be.

12-10-2012, 03:13 AM	#1
FloatMonkey Registered User Join Date: Jun 2012 Location: Santa Clarita, California Posts: 15	Fender Question So I got my 1970 GMC truck back from the body shop and the right front GMC V-8 1500 emblem was on crooked and the front chrome eyebrow piece does not fit correctly either. I know there is a differece between the Chevrolet and GMC fenders, what are those differences? Posted via Mobile Device Posted via Mobile Device

12-10-2012, 08:21 AM	#2
hugger6933 Registered User Join Date: Oct 2008 Location: Marianna Arkansas Posts: 7,261	Re: Fender Question The differences would not effect your problems. The boy lines at the front of the GMC are different like a 68 Chevy around the front grille opening where the moulding attaches. Most likely it they have installed a new fender, the holes are not there if I remember correctly. So they had to have drilled them at them shop, or they[the holes] were there and the stamper put them in crooked and that idea is not far fetched either. Jim

12-10-2012, 12:08 PM	#3
RenoKeene Florida Edition Join Date: Oct 2010 Location: Fruitland Park, FL Posts: 4,021	Re: Fender Question The fender emblem is a quick fix, elongate the stud holes a little. The emblem should hide the holes. As far as the eyebrow goes if it is a repop it probably won't fit worth a dam as the stamping is junk. Loosen the nuts inside the fender and move it around until your happy. I spent several hours getting mine where I wanted them to be. __________________ 70 GMC Short Stepside "Rose"-An American Beauty: Factory 402/TH400, AM/FM, AC, Tilt, Tach, Buckets, Posi, PS, PB, 3-5 Drop, Complete Resto-Rod 67 C-20 Slant Back Wrecker "Mad Max" 67 C-10 Ratrod "Step-N-Wolf" 71 Serro Scotty Sportsman camper "Scotty" 97 LT1 Z28 "The Hornet" Link to more pics of "Rose" http://67-72chevytrucks.com/vboard/a...p?albumid=1684 Check out my "Cheap Tricks" thread and add to it if you can, lots of good info there. http://67-72chevytrucks.com/vboard/s...d.php?t=489394



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.