|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
11-04-2003, 07:14 AM
|
#1 |
|
Senoir Member
Join Date: Mar 2002
Location: Rock Hill, SC USA
Posts: 1,214
|
4WD Front Axle question
Can the front 4WD axle be shortened on the hub ends by about 2" on each side. I want to put 4WD under a 54 and the front end in narrower than the 76 the axle & frame can out of. I still need to keep the spring mounts on the axle in the same place since I'm using the 76 frame under the 54. Any comments, I did not want to use a wimpy S-10 running gear.
__________________
67 Chevy, Small back glass, Factory 4WD, Factory Shortbed, Factory V8, Lifted 4" 70 GMC Sierra Grande, Factory Shortbed, Factory 402/400 turbo, Super Custom Interior. Numbers matching with SPID & Build Sheet. 68K Original Miles. Restored 2010 70 GMC Restoration Pictures http://67-72chevytrucks.com/gallery/...00&ppuser=4424 |
|
|
|
11-04-2003, 08:30 AM
|
#2 |
|
user # 2756
 
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
It can happen. I don't know how much it would cost for the machine work or new inner shafts, outers would not change.
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm 
|
|
|
|
|
11-04-2003, 10:31 AM
|
#3 |
|
Registered User
Join Date: Feb 2001
Location: Lake Stevens,WA 98258 North of Seattle
Posts: 833
|
I met a guy that put 3/4t chev axels (dana 44 & 14 bolt) under his Wrangler. If I remember right he had to get new axles for the rear, but was able to cut the front axels and have them re-splined. The axel tubs were cut and rewelded.
I have never done this, but just info I gathered by talking to the guy.
__________________
Marysville, WA (Dan72cst@hotmail.com) 72 4wd Blazer CST 350/350 72 4wd Chevy LWB 350/350 68 2wd Chevy LWB 327/400 |
|
|
|
|
11-04-2003, 12:23 PM
|
#4 |
|
Collector of rusty Items
Join Date: Dec 2001
Location: Sisters,Oregon USA
Posts: 731
|
They can be shortened and it is pretty common in the jeep world as lots of guys narrow dana 60 axles for a jeep.
here are some links: http://www.4x4wire.com/jeep/tech/axle/yjrcdana44/ http://www.off-road.com/~jweed/dana60.htm http://www.fabworxinc.com/Automotive...s_narrowed.htm good luck
__________________
Scrub Sisters, Oregon - Home of the Sisters Rodeo. 70 GMC 1,000,000 + miles 72 K-20 project, 456 Dana60 front, Corp14 rear w/locker, 265R19.5 tires 20-ply. Warn 12k winches both ends, Cross-over steering with raised tie-rod, Powerbox steering, 4500 watt 120-AC power, Air, Hydraulic aux power, 4 inch lift, 5000 lb air-bags both ends. |
|
|
|
|
11-04-2003, 12:59 PM
|
#5 |
|
Firefighter
Join Date: Feb 2001
Location: Yellville, Ar, USA
Posts: 1,943
|
If I am not mistaken the axle on a jeep truck is narrower than one on a Chevrolet truck.
__________________
'72 Chevy SWB 350 Auto '67 GMC LWB 350 4 speed '70 Chevy 4x4 Stepside 350 Auto Yellville, Ar. USA  
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
