How do I two tone with shaved drip rails - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jcblue · 03-01-2013, 07:44 PM

So I have a problem I need suggestions on. I have shaved my drip rails and have used a piece of 1/4 round. Body work is done and in primer. I have been drilling holes for moulding before paint and now I'm not sure how to go about separating the colors from the cab and roof. I could still use the trim on the cab but it originally tucked behind the drip rail now it will stand open on the end an look bad.. Any suggestions? I guess I could just do a solid color but I like the two tones
Posted via Mobile Device

brad_man_72 · 03-01-2013, 08:07 PM

Posted via Mobile Device

Like this....
Posted via Mobile Device

cdowns · 03-01-2013, 08:09 PM

use masking tape

SS Tim · 03-01-2013, 08:10 PM

Might try working the end down to a rounded or spear tip. Or even a flat roll then blending to shape. If there is not enough metal to do that consider buying the bulk trim from a trimmer that uses it for vinyl top work. It clips on the same way and is soft aluminum. A painted pinstripe would work to separate but you have holes already correct?

Edit This is the problem as I read it.

brad_man_72 · 03-01-2013, 08:27 PM

Quote:

Originally Posted by SS Tim

Might try working the end down to a rounded or spear tip. Or even a flat roll then blending to shape. If there is not enough metal to do that consider buying the bulk trim from a trimmer that uses it for vinyl top work. It clips on the same way and is soft aluminum. A painted pinstripe would work to separate but you have holes already correct?

Edit This is the problem as I read it.

I see now

Posted via Mobile Device

jcblue · 03-02-2013, 12:36 AM

Yes SS trim.. That's what I'm talking about.. Where can I find those ends your referring to. I'm interested to take a look. There are no pegs or holes btw.. I just wasn't sure a painted stripe would "flow" with all the other trim on the truck
Posted via Mobile Device

SS Tim · 03-02-2013, 01:39 AM

Was thinking you could work down the existing end of the molding. Or like I said source some new aluminum trim stock and work that, it could even be one piece with work and care. A painted stripe would be a simple break but as you point out flat and without depth. Another solution might be to use a finer than stock profile adhesive molding. These used to be so easy to get, now I am not so sure. An autobody/paint supply would be my first stop to look at samples or maybe online.

As an example of a fine adhesive molding here are some intended for wheel wells. Might try for some samples to play with.
http://www.customautotrim.com/produc.../wheelwell.htm

jcblue · 03-02-2013, 01:31 PM

Better clarification
Posted via Mobile Device

03-01-2013, 07:44 PM	#1
jcblue Registered User Join Date: Aug 2007 Location: Elkton, ky Posts: 385	How do I two tone with shaved drip rails So I have a problem I need suggestions on. I have shaved my drip rails and have used a piece of 1/4 round. Body work is done and in primer. I have been drilling holes for moulding before paint and now I'm not sure how to go about separating the colors from the cab and roof. I could still use the trim on the cab but it originally tucked behind the drip rail now it will stand open on the end an look bad.. Any suggestions? I guess I could just do a solid color but I like the two tones Posted via Mobile Device

03-01-2013, 08:07 PM	#2
brad_man_72 the boat guy Join Date: Jul 2007 Location: springfield mo Posts: 2,339	Re: How do I two tone with shaved drip rails Posted via Mobile Device Like this.... Posted via Mobile Device Attached Images __________________ 67, swb, fleet, tach, throttle, 5.3, 4l60e, 3.73's, fuel cell, 5 lug, p.d.b., 4-6 drop. great little truck 66, stevens drag/ski 18' silouette, 350, 2.02 doublehump heads. comp extreme marine 278 cam, vette 7 fin valve covers, old polished edelbrock intake, velvetdrive, casale v-drive, adj cavitation plate. 28, model a rpu project,

03-01-2013, 08:09 PM	#3
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	Re: How do I two tone with shaved drip rails use masking tape __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

03-01-2013, 08:10 PM	#4
SS Tim Registered User Join Date: Aug 2010 Location: Edwards, CA Posts: 7,503	Re: How do I two tone with shaved drip rails Might try working the end down to a rounded or spear tip. Or even a flat roll then blending to shape. If there is not enough metal to do that consider buying the bulk trim from a trimmer that uses it for vinyl top work. It clips on the same way and is soft aluminum. A painted pinstripe would work to separate but you have holes already correct? Edit This is the problem as I read it. Attached Images __________________ Thanks, Tim * VIN/Model Decoders * Power Team Charts (engine/transmission/gear ratio) * Post Your Pickup SPID Blazer SPID Suburban/Panel SPID * RTFM ... Read The Factory Manuals... download 'em here Highlanders Do you have a 1972 Plaid Pickup? Plaid Blazer ** Plaid Suburban Last edited by SS Tim; 03-01-2013 at 08:20 PM.

03-02-2013, 12:36 AM	#6
jcblue Registered User Join Date: Aug 2007 Location: Elkton, ky Posts: 385	Re: How do I two tone with shaved drip rails Yes SS trim.. That's what I'm talking about.. Where can I find those ends your referring to. I'm interested to take a look. There are no pegs or holes btw.. I just wasn't sure a painted stripe would "flow" with all the other trim on the truck Posted via Mobile Device

03-02-2013, 01:39 AM	#7
SS Tim Registered User Join Date: Aug 2010 Location: Edwards, CA Posts: 7,503	Re: How do I two tone with shaved drip rails Was thinking you could work down the existing end of the molding. Or like I said source some new aluminum trim stock and work that, it could even be one piece with work and care. A painted stripe would be a simple break but as you point out flat and without depth. Another solution might be to use a finer than stock profile adhesive molding. These used to be so easy to get, now I am not so sure. An autobody/paint supply would be my first stop to look at samples or maybe online. As an example of a fine adhesive molding here are some intended for wheel wells. Might try for some samples to play with. http://www.customautotrim.com/produc.../wheelwell.htm __________________ Thanks, Tim * VIN/Model Decoders * Power Team Charts (engine/transmission/gear ratio) * Post Your Pickup SPID Blazer SPID Suburban/Panel SPID * RTFM ... Read The Factory Manuals... download 'em here Highlanders Do you have a 1972 Plaid Pickup? Plaid Blazer ** Plaid Suburban

03-02-2013, 01:31 PM	#8
jcblue Registered User Join Date: Aug 2007 Location: Elkton, ky Posts: 385	Re: How do I two tone with shaved drip rails Better clarification Posted via Mobile Device Attached Images



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.