![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Jul 2010
Location: dublin, ca
Posts: 155
|
brake light switch - pict request
I have a 72 C10, the brake light switch seems to be jimmy-rigged into place. I was hoping someone has a pict of what it's supposed to look like above the foot pedal. Thanks guys
![]() |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Jul 2010
Location: dublin, ca
Posts: 155
|
Re: brake light switch - pict request
bump
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Aug 2010
Location: Prince George, BC
Posts: 3
|
Re: brake light switch - pict request
Auto or man trans?
|
![]() |
![]() |
![]() |
#4 |
Registered User
![]() Join Date: May 2009
Location: Pemberton, BC
Posts: 1,075
|
Re: brake light switch - pict request
Maybe this will help you out some.......
__________________
My goal in life is to be as good a person as my dog already thinks I am - Unknown |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jul 2010
Location: dublin, ca
Posts: 155
|
Re: brake light switch - pict request
that pict slightly helps. Thank you.
Its a 4speed manual |
![]() |
![]() |
![]() |
#6 |
Registered User
![]() Join Date: May 2009
Location: Pemberton, BC
Posts: 1,075
|
Re: brake light switch - pict request
This is the best pic I can get from my '68, taken from the left side of the steering column, looking up. Maybe you can make sense of this.
__________________
My goal in life is to be as good a person as my dog already thinks I am - Unknown |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Jul 2009
Location: Russellville, Arkansas
Posts: 1,699
|
Re: brake light switch - pict request
It should have a plate with a hole in it to mount to. Put the threaded end through, put the nut on and adjust the 2 nuts to where the lights come on when brake depressed, go off when not.
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Jul 2010
Location: dublin, ca
Posts: 155
|
Re: brake light switch - pict request
ok its the same it appears... But the only problem is my brake pedal. The part that physically hits the switch, seems to be gone... -.-
|
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Jul 2010
Location: dublin, ca
Posts: 155
|
Re: brake light switch - pict request
ps. thank you for the pict GruntMoanCough
|
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Aug 2011
Location: Atlanta, GA
Posts: 1,523
|
Re: brake light switch - pict request
Trying to figure this out...is there a way to tell the difference on what side the wires go on! I.e. a "+" on either prong?
Asking because I'm finishing up my painless harness install... Posted via Mobile Device
__________________
Best Regards, Leon M. Instagram: @TheDirtyDianah
Bagged | 6.0L LS | T-56 (6-Speed Manual) | Turbo Burnout/Rolling Video: Chevy C10 Stepside 6.0L LSx & 6-Speed Manual |
![]() |
![]() |
![]() |
#11 |
Restoration Virgin!
Join Date: Jan 2008
Location: Huntersville, NC
Posts: 8,298
|
Re: brake light switch - pict request
check this thread for a close up picture...http://67-72chevytrucks.com/vboard/s...d.php?t=516224
__________________
Geoff with a G 1968 Chevy C10 SWB The Mistress 1972 Custom Deluxe C20 Suburban A Suburban Named Isabella 1966 Ford Mustang Mama's High School Graduation Present |
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Aug 2011
Location: Atlanta, GA
Posts: 1,523
|
Re: brake light switch - pict request
Thank you, Geoff!
Posted via Mobile Device
__________________
Best Regards, Leon M. Instagram: @TheDirtyDianah
Bagged | 6.0L LS | T-56 (6-Speed Manual) | Turbo Burnout/Rolling Video: Chevy C10 Stepside 6.0L LSx & 6-Speed Manual |
![]() |
![]() |
![]() |
#13 |
Registered User
![]() Join Date: Nov 2012
Location: orlando, FL
Posts: 52
|
Re: brake light switch - pict request
does it matter what wire you hook up the ecm/tcm brake switch leads too? orange or white?
|
![]() |
![]() |
![]() |
#14 |
Senior Member
![]() Join Date: Oct 2009
Location: Godley, TX
Posts: 17,962
|
Re: brake light switch - pict request
No, does not matter which terminal each wire connects to - switch is just a circuit interrupter. Pressing the pedal lets the switch pop open and close the circuit to light the lights.
Posted via Mobile Device |
![]() |
![]() |
![]() |
Bookmarks |
|
|