Anyone into wood working or? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Gumby · 09-09-2013, 06:34 PM

Anyone into wood working or?

Ive seen them guys on weekend TV shows take a router and trim down a wood edge.

surley it owuld be done in plastic?

is there a bit that can take some 3/16 plastic, and turn the edge down to 1/8, only needs to be about 1/2 wide area turned down, rest of it can be 3/16

morons at moms work put lexan in her broken sun roof, but didn't size if for the seal to work.

**DPowers** · 09-09-2013, 06:42 PM

Rabbet Bit
http://www.pmcrouterbits.com/

Gumby · 09-09-2013, 06:52 PM

can you show me which one or link to one that will do that?

sort of lost at this

Zach B · 09-09-2013, 11:51 PM

The problem with plasic is it melts. Yes it can be done but you have to know how to cool it as you do it.
Posted via Mobile Device

**DPowers** · 09-10-2013, 08:46 PM

Quote:

Originally Posted by Gumby

can you show me which one or link to one that will do that?

sort of lost at this

Here is the link to the bit that you would use. Your local hardware should have it. You will need a router however. Lexan should be hard enough that it wouldn't melt. I would try a scrap piece first though.

http://www.pmcrouterbits.com/router-...outer-bit.html

PanelDeland · 09-12-2013, 08:37 PM

I would try a rotary saw.They're like a router but usually easier to control.

09-09-2013, 06:34 PM	#1
Gumby Registered User Join Date: Dec 2008 Location: NW-Ohio Posts: 2,525	Anyone into wood working or? Anyone into wood working or? Ive seen them guys on weekend TV shows take a router and trim down a wood edge. surley it owuld be done in plastic? is there a bit that can take some 3/16 plastic, and turn the edge down to 1/8, only needs to be about 1/2 wide area turned down, rest of it can be 3/16 morons at moms work put lexan in her broken sun roof, but didn't size if for the seal to work.

09-09-2013, 06:42 PM	#2
DPowers One foot in front of the other Join Date: Aug 2008 Location: Parrottsville, TN Posts: 5,442	Re: Anyone into wood working or? Rabbet Bit http://www.pmcrouterbits.com/ __________________ DP's 66 Build http://67-72chevytrucks.com/vboard/s...d.php?t=361556

09-09-2013, 06:52 PM	#3
Gumby Registered User Join Date: Dec 2008 Location: NW-Ohio Posts: 2,525	Re: Anyone into wood working or? can you show me which one or link to one that will do that? sort of lost at this

09-09-2013, 11:51 PM	#4
Zach B Registered User Join Date: Jun 2013 Location: El Dorado Springs Missouri Posts: 246	Re: Anyone into wood working or? The problem with plasic is it melts. Yes it can be done but you have to know how to cool it as you do it. Posted via Mobile Device

09-12-2013, 08:37 PM	#6
PanelDeland I am a Referee of life. Join Date: Jun 2000 Location: Greensboro N.C. Posts: 13,992	Re: Anyone into wood working or? I would try a rotary saw.They're like a router but usually easier to control. __________________ The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil"



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.