|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
10-17-2013, 06:03 PM
|
#1 |
|
Registered User
Join Date: Oct 2013
Location: anderson south carolina
Posts: 11
|
gauge cluster wont fit??
I recently puchased an 84 C30 and decided to replace all the gauges and gauge mount ( the bluish piece the gauges attach to) along with new clear lens and circuit on the back.I got it all together and it all went together without a problem but the bluish mount will not get close to where it screws in on the metal dash.the holes look right but i cannot get it through the metal opening because the mount seems as if it is to big.
Last edited by ramo; 10-17-2013 at 06:12 PM. |
|
|
|
10-17-2013, 06:08 PM
|
#2 |
|
Registered User
Join Date: Sep 2009
Location: Beaverton, OR from WA State
Posts: 1,515
|
Re: gauge cluster wont fit??
I do not know if your cluster housing (your bluish part) is aftermarket or not but I know my OEM one is a tight fit. Almost has to go in at a bit of an angle, I think right side first then left. It generally takes me a little finagling to get it in, the more I think about it, the more I think it's straight in at first then right edge and lastly left.
__________________
Devin 1983 GMC High Sierra 2500, 4x4, RC/LB, 400 S.B., SM-465, NP-208, Corporate 10 bolt & 9.5" 14 bolt 1996 GMC Sierra SLE 3500 DRW, 4x4, EC/LB, Vortec 454, NV-4500, BW-4401, AAM 925 & AAM 1050 1997 GMC Sierra SLT 1500 4x4, Z71/F44, EC/SB, Vortec 350 My Introduction with my '83s History New Daily, the '96 |
|
|
|
|
10-17-2013, 06:15 PM
|
#3 |
|
Registered User
Join Date: Oct 2013
Location: anderson south carolina
Posts: 11
|
Re: gauge cluster wont fit??
The right side is on the money and i can screw it down but the left side wont even get close to the holes,i pushed and jiggled it as hard as i dared and still nothing.
|
|
|
|
|
10-17-2013, 06:26 PM
|
#4 |
|
Registered User
Join Date: Oct 2013
Location: anderson south carolina
Posts: 11
|
Re: gauge cluster wont fit??
Hey thanks 83GMCK2500,i actually had to lift up and literally squeeze it behind the lip of the dash metal and now it sits flush,Dont you just love the 80's.
|
|
|
|
|
10-17-2013, 06:26 PM
|
#5 |
|
Registered User
Join Date: Dec 2010
Location: Visalia, Ca
Posts: 707
|
Re: gauge cluster wont fit??
If I remember right the right edge of the housing goes behind the dash as well
__________________
<Brandon> 1974 Chevrolet K5 Blazer 350sbc/SM465/NP205, dana44 front, corp 14bolt rear with 4.10s and a powertrax locker, custom rear bumper 400sbc in the works.  1981 GMC C1500 stepside 250i6, 3spd, 12bolt with 3.08s 2.5/4drop on 15x10 with 275/50r15 81 GMC C3500 cab-chassis dually with utility bed 350sbc, Sm465, 14bolt with 4.10s nv4500 getting ready to go in 1979 Chevrolet K5 R.I.P. http://67-72chevytrucks.com/vboard/s...d.php?t=434096 1976 Chevrolet C10 R.I.P. http://67-72chevytrucks.com/vboard/s...d.php?t=434195 |
|
|
|
|
10-17-2013, 07:39 PM
|
#6 |
|
Registered User
Join Date: Oct 2013
Location: anderson south carolina
Posts: 11
|
Re: gauge cluster wont fit??
The Right side and the bottom left go behind the metal.after that it was breeze.
|
|
|
|
|
10-17-2013, 08:46 PM
|
#7 |
|
Registered User
Join Date: Oct 2013
Location: anderson south carolina
Posts: 11
|
Re: gauge cluster wont fit??
The Right side and the bottom left go behind the metal.after that it was breeze.
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
