Need Some Advise... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ItsRandy · 01-09-2014, 10:38 PM

I am expecting the last piece of wood for my bed tomorrow (it's complicated) and will need to stain and finish the wood ASAP after I receive the last board. What kind of clear have other people used? I was going to use Spar Varnish but have read it remains "soft" when it dries. I have considered urethane but I don't think there is any UV protection in it. I would like to spray on the finish because I'm not real good with a paint brush (I hate brush marks) and most clears have no instructions for spraying. I have considered using automotive clear but don't know if it is compatible with oil based wood stain. Any help would be appreciated.

If I posted this in the wrong place might a moderator please move it. Thanks!

**FirstOwner69** · 01-09-2014, 11:11 PM

I used Minwax Spar Urethane semi-gloss. It contains a high level of UV blockers. I brushed it on (5 coats, first 2 thinned) and it flowed after brushing so no brush marks were left. It also is expands and contracts with the wood. It does not seem soft to me. The wood almost looks as if it's sealed in plastic. Mar-K has lots of info and test results for many finishes.

Mar-K link: http://www.mar-k.com/installation_hints.aspx

70LonghornCST · 01-10-2014, 12:32 AM

Hello ItsRandy!
Just to offer up a bit of knowledge from our FAQ section, this thread Wood Bed Finishing 101 may contain the advice that your are looking for. Good luck on your bed!
-Richard

01-09-2014, 10:38 PM	#1
ItsRandy Registered User Join Date: Nov 2010 Location: Grand Terrace, Ca. Posts: 1,607	Need Some Advise... I am expecting the last piece of wood for my bed tomorrow (it's complicated) and will need to stain and finish the wood ASAP after I receive the last board. What kind of clear have other people used? I was going to use Spar Varnish but have read it remains "soft" when it dries. I have considered urethane but I don't think there is any UV protection in it. I would like to spray on the finish because I'm not real good with a paint brush (I hate brush marks) and most clears have no instructions for spraying. I have considered using automotive clear but don't know if it is compatible with oil based wood stain. Any help would be appreciated. If I posted this in the wrong place might a moderator please move it. Thanks!

01-09-2014, 11:11 PM	#2
FirstOwner69 Senior Member Join Date: May 2010 Location: Wisconsin & Arizona Posts: 4,852	Re: Need Some Advise... I used Minwax Spar Urethane semi-gloss. It contains a high level of UV blockers. I brushed it on (5 coats, first 2 thinned) and it flowed after brushing so no brush marks were left. It also is expands and contracts with the wood. It does not seem soft to me. The wood almost looks as if it's sealed in plastic. Mar-K has lots of info and test results for many finishes. Mar-K link: http://www.mar-k.com/installation_hints.aspx

01-10-2014, 12:32 AM	#3
70LonghornCST Moderator Join Date: Jun 2008 Location: Modesto, CA Posts: 5,775	Re: Need Some Advise... Hello ItsRandy! Just to offer up a bit of knowledge from our FAQ section, this thread Wood Bed Finishing 101 may contain the advice that your are looking for. Good luck on your bed! -Richard __________________ 2018 Chevy Crew Cab 2006 Impala SS 1965 Plymouth Sport Fury 1970 Chevy Longhorn Bucket Seats Shoulder Belts Front Tow Hooks Factory Air Factory Speedwarning, Tach & Vaccum Factory Tilt CST Package AM/FM Radio Bumper Guards Richard 70 Longhorn CST Build Adding an AM/FM Decal



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.