Porter Rack n Pinion Steering

[62 Bowtie]

Anyone have pics of there rack setup with the power steering pump and hoses? Also what pump and hoses did you use meaning part numbers or vehicle you asked for parts since most trucks didnt come with rack n pinion steering thanks, Tony

[lolife99]

Porterbuilt uses a 79-93 mustang rack.
Your pump will greatly depend on the engine it's going on.
SBC?
BBC?
Long water pump?
Short water pump?

Contact Nate Porter.
He can get you the part number for the correct P/S hose kit for the rack.

[lolife99]

http://www.porterbuiltfabrication.co...and-Pinion-289

http://www.unisteer.com/power_steeri...cessories.html

[62 Bowtie]

thanks lolife yeah im useing the unisteer rack from PB SBC long water pump

[PBFAB.COM]

Originally Posted by 62 Bowtie

thanks lolife yeah im useing the unisteer rack from PB SBC long water pump

We offer a hose kit with fittings for $105. It's a tight squeeze and the position of the pump and style will dictate the routing.

Give us a buzz and we can discuss a few things and help you get situated.

[62 Bowtie]

Thanks!

[Sick5]

can we use any GM power steering pump or do we need a certain pump?

[PBFAB.COM]

Originally Posted by Sick5

can we use any GM power steering pump or do we need a certain pump?

You can use any chevy pump. One thing to keep in mind is that the pressure rating of the chevy pump is higher than the pressure rating of the Ford rack. You may decide to use a pressure regulator to tune in the "feel".

[JNJchev77]

Not trying to high jack....

But what about guys running an LS series motor? Can we use the newer factory hoses if using the truck accessory brackets?

[PBFAB.COM]

Originally Posted by JNJchev77

Not trying to high jack....

But what about guys running an LS series motor? Can we use the newer factory hoses if using the truck accessory brackets?

You can use the newer pump with our hose kit. You might be able to have new ends crimped on the factory hoses to save a little cash.

[Sick5]

Were would I be able to find a pressure regulator
Posted via Mobile Device

[JNJchev77]

Originally Posted by Porterbuilt Street Rods

You can use the newer pump with our hose kit. You might be able to have new ends crimped on the factory hoses to save a little cash.

Thanks Nate! I will hit you up for the hose kit!

[PBFAB.COM]

Originally Posted by Sick5

Were would I be able to find a pressure regulator
Posted via Mobile Device

I would give Borgeson a call.

We have run several without reducing the pressure with good results and zero issues.

[Sick5]

So hoses... would I be able you use my same hoses.?

And thanks for answering our question.
Posted via Mobile Device

[PBFAB.COM]

Originally Posted by Sick5

So hoses... would I be able you use my same hoses.?

And thanks for answering our question.
Posted via Mobile Device

You would have to have new ends put on the factory hoses to adapt to a 6AN male fitting. I think it would be easy to find a local hose and hydraulic shop that could crimp them on. We sell the fittings that screw into the rack housing and have the 6AN male for the hose connection.

Price it out for a local place... our hose kit with the proper fittings runs $105.

[BigShoe24]

I ran the 14mm & 16mm with oring's and unfortunately the nipple does not fit down inside the female inset. Is is ok to run these conversion fitting without the oring portion and just us hyrdaulic loctite? Thanks,

[PBFAB.COM]

The problem is that the threads in the rack are not metric, but standard. We have the correct standard to an fittings in stock if you need them.

Nate
Posted via Mobile Device

[BigShoe24]

Ahhh, well that explains it. I'll hopefully call the shop tomorrow to order a set. As always, thanks!

[BigShoe24]

Nate,

Do you have a picture of the fitting? I'm having some issues with my pressure side.

Thanks

[PBFAB.COM]

Originally Posted by BigShoe24

Nate,

Do you have a picture of the fitting? I'm having some issues with my pressure side.

Thanks

Shoot me an email tomorrow. I will send you a set. Nate@pbfab.com

Nate