|
05-19-2014, 05:59 PM
|
#1 |
|
Rusty Rockerfeller
 Join Date: May 2003
Location: South Georgia
Posts: 1,631
|
Chevy P80 parts help.
Picking up a 1987 Chevy P-80 step van with the 427. The water pump is bad. Would it be the same as a 454?
|
|
|
|
05-19-2014, 09:39 PM
|
#2 |
|
Robert Olson Transport
 
Join Date: Oct 2002
Location: recent transplant to NC USA
Posts: 20,310
|
Re: Chevy P80 parts help.
I don't know for sure but I know there is a difference between a vette 427 and a truck 427 and ive had issues getting parts for the truck motor
__________________
Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!! |
|
|
|
|
05-20-2014, 05:22 AM
|
#3 |
|
Rusty Rockerfeller
Join Date: May 2003
Location: South Georgia
Posts: 1,631
|
Re: Chevy P80 parts help.
Thanks. I actually went online with Oreillys auto parts and they had a listing for a Chevy C60 with a 427.
|
|
|
|
|
05-20-2014, 08:02 AM
|
#4 |
|
Registered User
Join Date: Mar 2012
Location: edgartown mass
Posts: 852
|
Re: Chevy P80 parts help.
all truck big blocks are the same but the tall decks. and those just have a little longer dizzy as far as i know. the vetts and car blocks are short decks and the vett has a diff water pump do to room from what i know. all my big blocks i get the same parts for but are all reg car even the one truck i got.(396 427(2) 454)
__________________
1986 c20 "the hillbilly" 350 sm465 3.42gears 21mpg at 70mph 1985 k30 "the ice cream truck from hell" no rust az truck 197-8??? c30 "ramp truck" 454 1978 monte carlo 350 350th with 2.73 gears. no rust. sc car |
|
|
|
|
05-20-2014, 09:17 AM
|
#5 |
|
Registered User
Join Date: Dec 2010
Location: Pittsburgh, PA
Posts: 1,009
|
Re: Chevy P80 parts help.
Looks like you have a tall deck, judging by the thermostat housing. It's kind of hard to tell, but do you have a thermostat housing that has one or two thermostats in it? If it has two, you have a tall deck. Order one from the C60 in that case. If you have a standard deck height block, just order one from any car or truck with a 454.
By the way, the tall decks had a special intake, different distributor, usually a deep sump oil pan and longer oil pump pickup, and usually forged internals. They're a good starting point for forced induction builds. I had a 366TDBBC I got for free once that I was considering doing a single turbo build on. There were some unforseen problems with it though and I had to sell it.
__________________
Steve Member of the Foot Pedal Club '83 Chevy K20: 6" Rough Country, 3" Performance Accessories BL, Bushwacker Cutouts, 38x15.50 Mickey Thompson Baja Claws, 350 HP 350 crate engine from Jegs, Turbo 400 
|
|
|
|
|
05-20-2014, 10:10 AM
|
#6 | |
|
Robert Olson Transport
Join Date: Oct 2002
Location: recent transplant to NC USA
Posts: 20,310
|
Re: Chevy P80 parts help.
Quote:
__________________
Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!! |
|
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
