|
05-28-2014, 11:28 PM
|
#1 |
|
Registered User
Join Date: Jun 2004
Location: Saskatchewan, Canada
Posts: 1,368
|
Motor plate guys
How much did you leave on your motor plate when you trimmed it down? I have my pattern at this stage right now, I had more on the outer edges as when I finish off my cage I'd like to attach a couple more tabs from the forward bars to the plate, then trimmed it a bit more.
I think I should still be able to add the extra attachment point if I cut it like this, if you run a motor plate please post some pictures of how you did yours.   
__________________
Speed is just a matter of money, question is how fast can you afford to go? 8.95@148.97mph all motor haven't tried bottle yet Sponsored by: Getz Oilfield Consulting Hard Candy Customs |
|
|
|
05-29-2014, 12:52 AM
|
#2 |
|
Registered User
Join Date: Apr 2003
Location: Stilwell, OK
Posts: 83
|
Re: Motor plate guys
I trimmed mine to the exact width of the frame.
__________________
Justin weight 3480 with driver 1.35 60ft 6.13@111mph 1/8 mile 9.80@131mph 1/4 mile 434 small block all motor |
|
|
|
|
05-29-2014, 01:06 AM
|
#3 |
|
Registered User
Join Date: Jun 2004
Location: Saskatchewan, Canada
Posts: 1,368
|
Re: Motor plate guys
I was thinking supports off the bars to the plate like you did, thanks for the picture.
__________________
Speed is just a matter of money, question is how fast can you afford to go? 8.95@148.97mph all motor haven't tried bottle yet Sponsored by: Getz Oilfield Consulting Hard Candy Customs |
|
|
|
|
05-29-2014, 01:08 AM
|
#4 |
|
meowMEOWmeowMEOW
Join Date: Sep 2009
Location: MKE WI
Posts: 7,128
|
Re: Motor plate guys
I"m no help, but 71dragtruck, your engine bay is purdy.
__________________
'66 Short Step / SD Tuned / Big Cam LQ4 / Backhalfed /Built 4l80e / #REBUILDEVERYTHING  |
|
|
|
|
05-29-2014, 01:16 AM
|
#5 |
|
Registered User
Join Date: Nov 2007
Location: Bay Area, Ca
Posts: 2,841
|
Re: Motor plate guys
Mine is like yours in the pic but flush with the outer edge of the frame.
__________________
------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49 |
|
|
|
|
05-29-2014, 01:20 AM
|
#6 |
|
Registered User
Join Date: Apr 2003
Location: Stilwell, OK
Posts: 83
|
Re: Motor plate guys
Here's a picture of the mount without the plate in the way.
__________________
Justin weight 3480 with driver 1.35 60ft 6.13@111mph 1/8 mile 9.80@131mph 1/4 mile 434 small block all motor |
|
|
|
|
05-29-2014, 01:51 AM
|
#7 |
|
Registered User
Join Date: Jun 2004
Location: Saskatchewan, Canada
Posts: 1,368
|
Re: Motor plate guys
Yes that's exactly how I was thinking of tying it in.
__________________
Speed is just a matter of money, question is how fast can you afford to go? 8.95@148.97mph all motor haven't tried bottle yet Sponsored by: Getz Oilfield Consulting Hard Candy Customs |
|
|
|
|
05-29-2014, 01:54 AM
|
#8 |
|
Registered User
Join Date: Jun 2004
Location: Saskatchewan, Canada
Posts: 1,368
|
Re: Motor plate guys
Not sure why my template looks like it hangs over the rail so much and angles out in the picture???
It is actually only about 1/4 over the edge and goes straight up on the sides.
__________________
Speed is just a matter of money, question is how fast can you afford to go? 8.95@148.97mph all motor haven't tried bottle yet Sponsored by: Getz Oilfield Consulting Hard Candy Customs |
|
|
|
|
05-29-2014, 08:11 AM
|
#9 |
|
Registered User
Join Date: Apr 2003
Location: Stilwell, OK
Posts: 83
|
Re: Motor plate guys
Are you going to install a mid plate also?
__________________
Justin weight 3480 with driver 1.35 60ft 6.13@111mph 1/8 mile 9.80@131mph 1/4 mile 434 small block all motor |
|
|
|
|
05-29-2014, 08:45 AM
|
#10 | |
|
Registered User
Join Date: Jun 2004
Location: Saskatchewan, Canada
Posts: 1,368
|
Re: Motor plate guys
Quote:
__________________
Speed is just a matter of money, question is how fast can you afford to go? 8.95@148.97mph all motor haven't tried bottle yet Sponsored by: Getz Oilfield Consulting Hard Candy Customs |
|
|
|
|
|
05-29-2014, 08:45 AM
|
#11 |
|
Senior Member
 
Join Date: Mar 2008
Location: tyler texas
Posts: 1,536
|
Re: Motor plate guys
__________________
NHRA Super Street 469C It only runs 10.90 at 156 mph |
|
|
|
|
05-29-2014, 08:49 AM
|
#12 |
|
Senior Member
Join Date: Mar 2008
Location: tyler texas
Posts: 1,536
|
Re: Motor plate guys
Mine is mounted to a plate that spans the frame rail top to bottom. Thats the best pic I have. You will also need to do something with engine limiters. Mine bolt to the old motor mount bosses on the block. They then went forward to the old crossmember. Make sure you use a quality rubber trans mount.
__________________
NHRA Super Street 469C It only runs 10.90 at 156 mph |
|
|
|
|
05-29-2014, 11:20 AM
|
#13 |
|
Registered User
Join Date: Jun 2004
Location: Saskatchewan, Canada
Posts: 1,368
|
Re: Motor plate guys
I'm running a Prothane poly mount and have a limiter for both sides.
__________________
Speed is just a matter of money, question is how fast can you afford to go? 8.95@148.97mph all motor haven't tried bottle yet Sponsored by: Getz Oilfield Consulting Hard Candy Customs |
|
|
|
|
05-29-2014, 05:58 PM
|
#14 |
|
It's Better With Nitro
Join Date: Apr 2008
Location: Chino Hills, CA
Posts: 2,261
|
Re: Motor plate guys
I fab'd my chassis mounts to index the motor plate, so I didn't have to muscle anything around - I welded a small tab as a lip for the bottom of the plate, and machined the angle on the ends of the plate to correspond with the angled vertical of the chassis mount - this worked as guides as the engine was dropped down.
 …it ended up being a smaller version of Jerry Bickel's plate mount: 
__________________
1963 C-10: Deluxe-optioned cab, shortbed, fleetside Pontiac 462 ci, Kauffman D-Port alum. heads 4L80E, narrowed sheetmetal Ford 9-inch Tubular front and rear suspension Custom 6-piston front disc and 4-piston rear disc brakes |
|
|
|
|
05-29-2014, 09:33 PM
|
#15 |
|
Registered User
Join Date: Jun 2004
Location: Saskatchewan, Canada
Posts: 1,368
|
Re: Motor plate guys
Very nice Vin, got mine trimmed down, time to mount it and round the edges.
__________________
Speed is just a matter of money, question is how fast can you afford to go? 8.95@148.97mph all motor haven't tried bottle yet Sponsored by: Getz Oilfield Consulting Hard Candy Customs |
|
|
|
|
05-30-2014, 07:45 PM
|
#16 |
|
Registered Truck Offender
Join Date: May 2008
Location: hells training ground (aka Ariz)
Posts: 3,118
|
Re: Motor plate guys
Vacuum pumps water pump etc is intended to be on the face of the motor plate.
But..... Alternators are always a PITA,, plan ahead  
__________________
Still playin with trucks, even at my age! When you're dead, it's only a problem for the people around you, because you don't know you're dead. .....It's kinda the same when your STUPID. I just did my taxes and reviewed my SS statement. Thanks to the current administration it looks like I will only have to work till noon on the day of my funeral. |
|
|
|
|
05-30-2014, 10:27 PM
|
#17 |
|
Registered User
Join Date: Jun 2004
Location: Saskatchewan, Canada
Posts: 1,368
|
Re: Motor plate guys
Got that covered Marv
 
__________________
Speed is just a matter of money, question is how fast can you afford to go? 8.95@148.97mph all motor haven't tried bottle yet Sponsored by: Getz Oilfield Consulting Hard Candy Customs |
|
|
|
 |
| Bookmarks |
|
|
\\ MY YOUTUBE CHANNEL
Linear Mode
