|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
10-28-2013, 11:04 PM
|
#1 |
|
Registered User
Join Date: Oct 2013
Location: Spokane, wa
Posts: 25
|
C10 C-notch finished process
Here is my process for my 75 c10 c notch process also has a axle flip kit and 2" lowering shackles
Last edited by Chrisxeasy; 10-28-2013 at 11:14 PM. |
|
|
|
10-28-2013, 11:05 PM
|
#2 |
|
Registered User
Join Date: Oct 2013
Location: Spokane, wa
Posts: 25
|
Re: C10 C-notch process
Photo two, bracket cut out
|
|
|
|
|
10-28-2013, 11:07 PM
|
#3 |
|
Registered User
Join Date: Oct 2013
Location: Spokane, wa
Posts: 25
|
Re: C10 C-notch process
Test fitting and drilling bolt holes
|
|
|
|
|
10-28-2013, 11:08 PM
|
#4 |
|
Registered User
Join Date: Oct 2013
Location: Spokane, wa
Posts: 25
|
Re: C10 C-notch process
Install bolts and washers and tighten
|
|
|
|
|
10-28-2013, 11:09 PM
|
#5 |
|
Registered User
Join Date: Oct 2013
Location: Spokane, wa
Posts: 25
|
Re: C10 C-notch process
C notch finished and 2" drop shackles installed
|
|
|
|
|
10-28-2013, 11:11 PM
|
#6 |
|
Registered User
Join Date: Oct 2013
Location: Spokane, wa
Posts: 25
|
Re: C10 C-notch process
Inside view of finished bolt on mcgauheys c-notch
|
|
|
|
|
10-29-2013, 12:02 AM
|
#7 |
|
Registered User
Join Date: Feb 2009
Location: slurrey, bc.
Posts: 1,134
|
Re: C10 C-notch finished process
looks good on the notch... but what's your pinion angle set at? looks a bit steep...
__________________
-'73 c/10 - Low with Go - will be complete... probably never. -'90 2wd Blazer - well... soon enough anyways. -'84 SWB - the daily gas guzzler. |
|
|
|
|
06-08-2014, 11:31 AM
|
#8 |
|
Registered User
Join Date: Nov 2013
Location: Ocean Springs, MS
Posts: 43
|
Re: C10 C-notch finished process
I noticed you only have to leafs on your springs. What is the ride quality like? And do you have plenty of travel with the notch?
|
|
|
|
|
06-09-2014, 09:23 AM
|
#9 |
|
Registered User
Join Date: Jan 2007
Location: vernon b.c.
Posts: 3,022
|
Re: C10 C-notch finished process
are hangers on backwards ?
|
|
|
|
|
06-09-2014, 11:52 AM
|
#10 |
|
I'm just glad to be here!
Join Date: Jan 2008
Location: Longview, TX
Posts: 4,788
|
Re: C10 C-notch finished process
I'd flip the shakles around...
__________________
Karl  1965 Chevy Stepside(Grandpa's Old Blue) and (July 2015 Shop Build!)(2020, the Saga Continues) http://67-72chevytrucks.com/vboard/s...d.php?t=372424 The LST Challenge: http://67-72chevytrucks.com/vboard/s...=1#post7812257 Korbin's 1st Square: "Sunburn" http://67-72chevytrucks.com/vboard/s...d.php?t=418618 1985 GMC Sierra: "White Trash", Korbin's 2nd now... http://67-72chevytrucks.com/vboard/s...d.php?t=632305 Henry - 1984 Chevrolet, Owen's 1st Square |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
