|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
07-01-2014, 06:59 AM
|
#1 |
|
Registered User
Join Date: Aug 2011
Location: confusion, USA
Posts: 206
|
Pulled a wire out of instrument panel socket... how the heck do they stay in?
alright I was replacing the bulbs in my instrument cluster, and as i was pulling out a socket, the wire pulled out, and the wiring is original and a bit stiff. but looking at the socket, how do they stay "in" there's no snap or anything for the wire to hold against the bulb to keep it lit and not have it fall right back out haha. I hate electrical stuff. this is on a 1955 chevy truck
will the 1955-56 chevy passenger car bulb sockets work on the 1955 2nd series trucks as well? |
|
|
|
07-01-2014, 11:02 AM
|
#2 |
|
Registered User
Join Date: Sep 2013
Location: Morro Bay, California
Posts: 447
|
Re: Pulled a wire out of instrument panel socket... how the heck do they stay in?
I rebuilt all my original sockets with part from here -
http://www.repairconnector.com/produ...Connector.html |
|
|
|
|
07-02-2014, 09:12 AM
|
#3 |
|
Registered User
Join Date: Oct 2010
Location: Ocean Springs, MS
Posts: 1,746
|
Re: Pulled a wire out of instrument panel socket... how the heck do they stay in?
There is a little tab crimped on to the end of the wire that makes contact with the bulb. If if pulls off, you can replace it with a blob of solder.
__________________
Gary 1971 Chevrolet C/10 1951 GMC 100 1977 GMC C15 1955 Chevrolet 3100 |
|
|
|
|
07-02-2014, 11:12 AM
|
#4 |
|
Registered User
Join Date: Jun 2006
Location: Idaho
Posts: 8,800
|
Re: Pulled a wire out of instrument panel socket... how the heck do they stay in?
I got mine at NAPA
__________________
1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread 1964 Chevelle Malibu w/ 355-350TH (daily driver) Helpful AD and TF Manual Site Old Car Manual Project |
|
|
|
|
07-02-2014, 01:35 PM
|
#5 |
|
Registered User
Join Date: Jan 2012
Location: Motown
Posts: 7,677
|
Re: Pulled a wire out of instrument panel socket... how the heck do they stay in?
good info orrieg with part number
i was going to suggest the solder blob too 
__________________
cool, an ogre smiley Ogre's 58 Truk buildhow to put your truck year and build thread into your signature shop air compressor timer |
|
|
|
|
07-02-2014, 03:34 PM
|
#6 |
|
Registered User
Join Date: Sep 2013
Location: Morro Bay, California
Posts: 447
|
Re: Pulled a wire out of instrument panel socket... how the heck do they stay in?
|
|
|
|
|
07-03-2014, 10:45 AM
|
#7 | |
|
Registered User
Join Date: Sep 2012
Location: Fishers, IN
Posts: 272
|
Re: Pulled a wire out of instrument panel socket... how the heck do they stay in?
Quote:
__________________
Just because you can, doesn't necessarily mean you should. 1959 3100 stepside 355 + T5 |
|
|
|
|
|
07-03-2014, 01:13 PM
|
#8 | |
|
Registered User
Join Date: Jun 2006
Location: Idaho
Posts: 8,800
|
Re: Pulled a wire out of instrument panel socket... how the heck do they stay in?
Quote:
__________________
1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread 1964 Chevelle Malibu w/ 355-350TH (daily driver) Helpful AD and TF Manual Site Old Car Manual Project |
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
