NY Cutting up old Cab / Extra parts

[DD1]

Originally Posted by MECCASPEEDKUSTOM

DD1 if you have the parts boxed up and PM me the dimensions I can get a quote via my UPS account, than i can just send you a label if that works out to be cheaper..... PM me you paypal info and total cost minus shipping....

Ok, I managed to box this thing up. I took a large box from home depot, opened it part way and stuck the stuff in. They are nicely bubble wrapped and ready to go. I hope the shipping quote you get works for you, because they were a pain to pack.

The box ends up being 43x43x9. The 9 is a rough estimate of it's widest point. It weighs about 16 pounds.

Let me know what you want to do. Thanks!

[MECCASPEEDKUSTOM]

Thanks DD1....!!!! Ill get a quote tomorrow at work and let you know asap... Shoot me your zip code...

[DD1]

Originally Posted by MECCASPEEDKUSTOM

Thanks DD1....!!!! Ill get a quote tomorrow at work and let you know asap... Shoot me your zip code...

Zip code would help, huh? 10901.

[Russ.W.]

Hey, sorry for being a pain, but I've had a mind change - again. I do want the left/drivers kick-panel vent if possible. Don't need the whole left side though, just a square cut around the vent opening itself.

Something like this:



Assuming the vent opening itself is in good condition. That'd be the difficult part to fabricate, so it'll make life easier.

[MECCASPEEDKUSTOM]

DD1... I guess you will have to sell the sheet-metal pieces to the next person in line...
because of the dimension UPS ground would cost 107.55 to get them from you to my shop..
With those dimension they go by the size instead of the weight so its like double the cost...

Sorry if it was a big inconvenience to package them up to ship... I do appreciate your efforts!

[DD1]

Originally Posted by MECCASPEEDKUSTOM

DD1... I guess you will have to sell the sheet-metal pieces to the next person in line...
because of the dimension UPS ground would cost 107.55 to get them from you to my shop..
With those dimension they go by the size instead of the weight so its like double the cost...

Sorry if it was a big inconvenience to package them up to ship... I do appreciate your efforts!

No problem. That is a ridiculous amount for shipping. I could not find a box that it would just fit in by itself. Sorry about that.

Jess, you are up. If you still want it, let's chat and we can arrange for you to pick up everything!

[DD1]

Originally Posted by Russ.W.

Hey, sorry for being a pain, but I've had a mind change - again. I do want the left/drivers kick-panel vent if possible. Don't need the whole left side though, just a square cut around the vent opening itself.

Something like this:

Assuming the vent opening itself is in good condition. That'd be the difficult part to fabricate, so it'll make life easier.

Hey, no problem. You want the drivers side (US drivers side not Australia), right? On that side it looks pretty good from the inside. I need to cut the cowl panel and see how it looks from the out side.

The passenger side is lousy, so I am surprised the drivers side is in decent shape. Here is a pic from the inside, and I will get a pic of the outside for you, probably tomorrow.

[zicc1835]

Ok thanks sounds good to me ill P M you my info
thanks again
Jess

Originally Posted by DD1

No problem. That is a ridiculous amount for shipping. I could not find a box that it would just fit in by itself. Sorry about that.

Jess, you are up. If you still want it, let's chat and we can arrange for you to pick up everything!

[Russ.W.]

Originally Posted by DD1

Hey, no problem. You want the drivers side (US drivers side not Australia), right? On that side it looks pretty good from the inside. I need to cut the cowl panel and see how it looks from the out side.

The passenger side is lousy, so I am surprised the drivers side is in decent shape. Here is a pic from the inside, and I will get a pic of the outside for you, probably tomorrow.

That looks great. Thank you ... and yes I do mean your drivers side, the left.

Suppose I should confirm now, you have no problem shipping to Australia? At my expense of course.

[DD1]

Originally Posted by Russ.W.

That looks great. Thank you ... and yes I do mean your drivers side, the left.

Suppose I should confirm now, you have no problem shipping to Australia? At my expense of course.

I don't have a problem sending it to Australia. I can only imagine the difficulty you have getting parts.

PM me the information I would need to figure out what shipping would be. I'll get you the pic of the outside a bit later when I go out to the garage. Hopefully it will be in good enough shape for you. Based on the inside I think it will be fine, but you never know.

[DD1]

Originally Posted by Russ.W.

That looks great. Thank you ... and yes I do mean your drivers side, the left.

Suppose I should confirm now, you have no problem shipping to Australia? At my expense of course.

Hey Russ, I sent you a PM. The outside does not look anywhere as nice as the inside.

[DD1]

Originally Posted by 68Bowtie4x4

That looks great DD1. I finally got the camper down to my house now after getting fuel in it and getting it fired up. It will be much easier to work on it now.

Thanks,

Doug

Hey Doug, i got your piece all boxed up and ready to ship. What's your zip code? I'll pic a random OR zip to get an estimate and PM you. I can figure out the actual cost when I get your actual zip.

[68Bowtie4x4]

Originally Posted by DD1

Hey Doug, i got your piece all boxed up and ready to ship. What's your zip code? I'll pic a random OR zip to get an estimate and PM you. I can figure out the actual cost when I get your actual zip.

Zip is 97801.

[DD1]

Originally Posted by 68Bowtie4x4

Zip is 97801.

PM Sent.

[DD1]

Originally Posted by 68Bowtie4x4

Zip is 97801.

Hey Doug, I sent you a PM. Repackaged it as you suggested. I think you will like the revised shipping price.

[68Bowtie4x4]

Received the back wall section today....Thank you very much!!!!

[DD1]

Originally Posted by 68Bowtie4x4

Received the back wall section today....Thank you very much!!!!

You are welcome. Thanks for your patience with me getting the piece cut off and sent to you.

[FL71C10]

I need a one foot long piece of the rear window lip. I found two little rust holes when I took my rear window out. They are on the outside of the cab, just under the rubber trim. So I would want a piece that goes from the lip, up about two inches into the roof.

If you need me to, I can post a pic of what I need

[DD1]

Originally Posted by FL71C10

I need a one foot long piece of the rear window lip. I found two little rust holes when I took my rear window out. They are on the outside of the cab, just under the rubber trim. So I would want a piece that goes from the lip, up about two inches into the roof.

If you need me to, I can post a pic of what I need

I can get you that, but a pic would help. I am not sure whether your rust holes are in the center, left, or right of the window. Post a pic, and we will work it out. Thanks!

[FL71C10]

OK, here are a couple of pictures. One is of the window lip, with the dimensions I think I need. The other one shows both holes. I think anywhere along the lip will be fine, except the radiused corner.

[DD1]

Originally Posted by FL71C10

OK, here are a couple of pictures. One is of the window lip, with the dimensions I think I need. The other one shows both holes. I think anywhere along the lip will be fine, except the radiused corner.

Yeah, I think I can do this. I'll send you a PM.

[DD1]

Originally Posted by FL71C10

OK, here are a couple of pictures. One is of the window lip, with the dimensions I think I need. The other one shows both holes. I think anywhere along the lip will be fine, except the radiused corner.

Hey, piece cut and being shipped out today! Sent you a PM with pics. Thanks!

[FL71C10]

Thanks, looks good. Have a good trip!

[DD1]

Originally Posted by FL71C10

Thanks, looks good. Have a good trip!

Thanks!