|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
12-02-2014, 12:18 AM
|
#1 |
|
Registered User
Join Date: Aug 2013
Location: Oswego New York
Posts: 25
|
1967 c10 with 250 inline won't stay running
I left work today and the truck ran fine and went to the gas station maybe a mile down the road to clean the windows and then the truck wouldn't run. It would fire then quit immediately. I help the key to start and it would still run then as soon as i let off it would quit so I pulled the fuel filter made sure there was no gunk in it then pulled the sending unit out of the tank and checked for blockage and there was nothing. Then it fire up and ran fine now it's doing it again and I can't get it going.
|
|
|
|
12-02-2014, 12:51 AM
|
#2 |
|
Registered User
Join Date: Aug 2014
Location: Hydro, OK
Posts: 7
|
Re: 1967 c10 with 250 inline won't stay running
Sounds like maybe a bad fuel cap causing a vacuum thus starving it for fuel. Try taking the cap off and see if it is getting fuel. If not, then you may be looking at a pump.
|
|
|
|
|
12-02-2014, 01:17 AM
|
#3 |
|
Senior Member
 
Join Date: Sep 2007
Location: Albuquerque NM
Posts: 7,862
|
Re: 1967 c10 with 250 inline won't stay running
Check your wiring to the coil and the wiring to the ignition switch for fraying. Or are you running an hei ignition?
__________________
1967custom |
|
|
|
|
12-02-2014, 09:11 AM
|
#4 |
|
Registered User
Join Date: Aug 2013
Location: Oswego New York
Posts: 25
|
Re: 1967 c10 with 250 inline won't stay running
I will do that as soon as i get home and yes I'm running hei
|
|
|
|
|
12-02-2014, 09:56 AM
|
#5 |
|
Registered User
Join Date: Aug 2013
Location: Oswego New York
Posts: 25
|
Re: 1967 c10 with 250 inline won't stay running
If the fuel pump is bad would it be better to swap to a electronic fuel pump or stay with the manual?
|
|
|
|
|
12-02-2014, 11:52 AM
|
#6 |
|
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: 1967 c10 with 250 inline won't stay running
check your vaccume lines for a break or one that slipped off
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
|
|
|
|
12-02-2014, 12:35 PM
|
#7 | |
|
Registered User
Join Date: Aug 2013
Location: Oswego New York
Posts: 25
|
Re: 1967 c10 with 250 inline won't stay running
Quote:
|
|
|
|
|
|
12-02-2014, 12:50 PM
|
#8 |
|
Registered User
Join Date: Sep 2013
Location: Cumming, Ga
Posts: 1
|
Re: 1967 c10 with 250 inline won't stay running
Sounds like a switch or wiring problem. Ign power when key in crank and not in run position. Jump a hot wire to HEI and start. If it stays running you know its the problem.
|
|
|
|
|
12-02-2014, 01:17 PM
|
#9 | |
|
Registered User
Join Date: Aug 2013
Location: Oswego New York
Posts: 25
|
Re: 1967 c10 with 250 inline won't stay running
Quote:
|
|
|
|
|
|
12-02-2014, 06:00 PM
|
#10 |
|
Registered User
Join Date: Aug 2013
Location: Oswego New York
Posts: 25
|
Re: 1967 c10 with 250 inline won't stay running
Ran a hot wire and it worked thank you for that. Now I know where to focus my time for a bit
|
|
|
|
|
12-02-2014, 07:48 PM
|
#11 |
|
Senior Member
Join Date: Sep 2007
Location: Albuquerque NM
Posts: 7,862
|
Re: 1967 c10 with 250 inline won't stay running
Sounds like maybe a bad ignition switch.
__________________
1967custom |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
