What did you get done 2/8/15 edition - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**old Rusty C10** · 02-08-2015, 09:05 PM

I got in the new carb for the plow truck because I cant get the old one to work anymore, changed the motor on the plow and think I finally got some stuff purchased for the project how about you all

NJ C10 Guy · 02-08-2015, 11:56 PM

Ordered some parts, and I think I'm getting a running 350 delivered to me for 500 bucks with an almost new edelbrock 1406. It's been too cold out to do anything!

Jaysonb · 02-09-2015, 12:25 AM

Did a cam swap, put bigger jets in the carb, and got headers put on. What a night and day difference!!

Ghostwhite · 02-09-2015, 03:12 AM

Changed the fuel pump on my 88 TBI CCLB dually. Test drive had it running ok after it got hot(old pump would overheat and pressure would drop to less than 4psi).

SCOTI · 02-09-2015, 09:07 AM

Sanded bondo on the bed floor then DA'd the floor & inner bed sides in preparation for the Line-X shoot.

Also went out & pulled everything used for a vacuum brake system between the master cyl to the pedal pad. I got the pedal assembly all cleaned up & painted. Now I just have to get it installed, swap the leaking master cyl out, repair the paint damage on my vac booster can, & bleed the brakes again.

peresich · 02-09-2015, 09:41 AM

Replaced the vacuum modulator and line on my transmission and am being taught a lesson in humility by slowly realizing I am going to have to let a professional fix my transmission instead of doing it myself in the garage.

**rs74** · 02-09-2015, 10:06 AM

Got all the interior swapped into the diesel short bed. Steam clean the carpets in the C10 and K30 too.

68Timber · 02-09-2015, 10:41 AM

Door pins and bushings on my CUCV. I regret having put that off so long, it was an easy job with an engine hoist holding the doors for me. Few minor adjustments and the doors close great now.

77K10Silverado · 02-09-2015, 10:59 AM

Chassis Saver on the back half.

Name: IMG_0632.jpg
Views: 80
Size: 41.7 KB

Name: IMG_0631.jpg
Views: 80
Size: 63.2 KB

Name: IMG_0639.jpg
Views: 81
Size: 39.8 KB

Name: IMG_0638.jpg
Views: 84
Size: 62.0 KB

Name: IMG_0640.jpg
Views: 77
Size: 29.6 KB

gmclowsierra · 02-09-2015, 11:06 AM

chassis saver the front floor of my sub and removed the trans crossmember to add exhaust cutouts.

laidlow91 · 02-09-2015, 11:17 AM

did the first test fit of the nv3500 in the suburban.
need to mark floor for cutting, install driveshft to meas. for length,
and get a meas for the hydraulic line length so i can get that made.

Shorthair_Hunter · 02-09-2015, 06:27 PM

I prepped my hd hubcaps for use with the manual hubs on my '85 K20. Hopefully new tires coming soon...

02-08-2015, 09:05 PM	#1
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,277	What did you get done 2/8/15 edition I got in the new carb for the plow truck because I cant get the old one to work anymore, changed the motor on the plow and think I finally got some stuff purchased for the project how about you all __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!

02-08-2015, 11:56 PM	#2
NJ C10 Guy Registered User Join Date: Sep 2014 Location: Toms River, NJ Posts: 437	Re: What did you get done 2/8/15 edition Ordered some parts, and I think I'm getting a running 350 delivered to me for 500 bucks with an almost new edelbrock 1406. It's been too cold out to do anything!

02-09-2015, 12:25 AM	#3
Jaysonb Registered User Join Date: May 2009 Location: Good Thunder Mn. Posts: 955	Re: What did you get done 2/8/15 edition Did a cam swap, put bigger jets in the carb, and got headers put on. What a night and day difference!!

02-09-2015, 03:12 AM	#4
Ghostwhite Squarebody guy Join Date: Apr 2009 Location: Minnesota Posts: 335	Re: What did you get done 2/8/15 edition Changed the fuel pump on my 88 TBI CCLB dually. Test drive had it running ok after it got hot(old pump would overheat and pressure would drop to less than 4psi).

02-09-2015, 09:07 AM	#5
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 21,941	Re: What did you get done 2/8/15 edition Sanded bondo on the bed floor then DA'd the floor & inner bed sides in preparation for the Line-X shoot. Also went out & pulled everything used for a vacuum brake system between the master cyl to the pedal pad. I got the pedal assembly all cleaned up & painted. Now I just have to get it installed, swap the leaking master cyl out, repair the paint damage on my vac booster can, & bleed the brakes again. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

02-09-2015, 09:41 AM	#6
peresich Registered User Join Date: Jan 2015 Location: Muscle Shoals, AL Posts: 20	Re: What did you get done 2/8/15 edition Replaced the vacuum modulator and line on my transmission and am being taught a lesson in humility by slowly realizing I am going to have to let a professional fix my transmission instead of doing it myself in the garage.

02-09-2015, 10:06 AM	#7
rs74 Senior Member Join Date: Jun 2010 Location: Illinois Posts: 2,957	Re: What did you get done 2/8/15 edition Got all the interior swapped into the diesel short bed. Steam clean the carpets in the C10 and K30 too. __________________ Roy 85 Short Bed Silverado- Work in progress. http://67-72chevytrucks.com/vboard/s...d.php?t=564818 1987 R10 shortie

02-09-2015, 10:41 AM	#8
68Timber I know the pieces fit Join Date: Nov 2007 Location: MONTGOMERY, AL Posts: 5,523	Re: What did you get done 2/8/15 edition Door pins and bushings on my CUCV. I regret having put that off so long, it was an easy job with an engine hoist holding the doors for me. Few minor adjustments and the doors close great now. __________________ John 79 2wd Blazer (Bruiser) 85 M1009 Blazer (Sarge) build 74 Honda Z50 build

02-09-2015, 10:59 AM	#9
77K10Silverado Registered User Join Date: Jul 2014 Location: Winston-Salem, NC Posts: 561	Re: What did you get done 2/8/15 edition Chassis Saver on the back half. __________________ *Mike B.* 77 K10 - http://67-72chevytrucks.com/vboard/s...=1#post6752641

02-09-2015, 11:06 AM	#10
gmclowsierra Registered User Join Date: Mar 2008 Location: williamsport,pa Posts: 329	Re: What did you get done 2/8/15 edition chassis saver the front floor of my sub and removed the trans crossmember to add exhaust cutouts.

02-09-2015, 11:17 AM	#11
laidlow91 Registered User Join Date: Nov 2013 Location: new boston, nh Posts: 19	Re: What did you get done 2/8/15 edition did the first test fit of the nv3500 in the suburban. need to mark floor for cutting, install driveshft to meas. for length, and get a meas for the hydraulic line length so i can get that made.

02-09-2015, 06:27 PM	#12
Shorthair_Hunter Registered User Join Date: Jan 2012 Location: Yakima WA Posts: 31	Re: What did you get done 2/8/15 edition I prepped my hd hubcaps for use with the manual hubs on my '85 K20. Hopefully new tires coming soon...



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.