AZ Cabs for parts/pieces

[t korinek]

I have 4 cabs getting ready to go to the crusher for parts, they were all non ac cabs, 1 is a small back window cab
Let me know if you need something, pieces are $20 & up depending on size & how much work & sawing it is to cut off & box up.
Thanks,
Tom

[Ol 67 C10]

Are you cutting up any of the frames? I need both front frame rail ends. PO cut mine off to install front roll pan. I need both front pieces cut back right behind the radiator support mounts. If you're able to do that give me quote with shipping to 22830 VA. Thanks!

[michael bustamante]

I need driver side lower half of kick panal and the floor attached. If you can pm me a e mail I can send you a pic

[Ol 67 C10]

I'm also interested in a patch where the gas pedal mounts to the floor. I need the same patches as michael for both sides at the kick panel if you have any good ones left after you get his piece for him. Also how much for the small window glass if its in good condition? Thanks!

[Nsanehotrodz]

How much for the entire cab in the last pic? I would like to see more pics!

[bigrigpardo]

I too would like to see more pics of the cab in the last pic. it looks very salvageable from what I am used too.

[jmedero]

Hey I'm looking for the mounting bracket for the wiper motor under the dash. It's the C looking bracket.

[t korinek]

jmedero have that piece $20 shipped

The other cab is not worth messing with in my opinion once you add shipping on to it, needs work in too many places.
I have some cabs that are better from $250 on up.


Heres some pics of the other cab areas were asking about, the kick panels have some rust down in the area where they meet, where the sand & water sit.

[t korinek]

a few more pics

[Ol 67 C10]

Any of them good around where the gas pedal mounts to the floor? And is that small back glass for sale? Thanks

[t korinek]

Here's the spot where the pedal mounts, its solid $30 + shipping, how big of an area do you need?
Rear small glass is cracked, I have a new clear one for $50 + shipping

[6t727t2]

Hey Tom, I'm looking for a really clean cowl section patch as outlined, as rust free as possible inside and out. Thanks, Harry

[jmedero]

I'll take it. What's paypal info?

[t korinek]

Harry, there is a nice one on this cab hows $35 + shipping

[6t727t2]

That works as long as it looks as good when cut. Shipping to 08015. Thanks

[67chevy4x4c]

How much for the inside cowl on the drivers side about 15 inchs of it . On the 67 cab and the kick panel on the on the drivers side 67 shipped to 24813 Bartley wva Thanks

[swamp rat]

On the 67 cab i'm looking for both inner and outer repair panels for my step thru cab, zip is 98387. here's a pic to show how big the panels need to be, from the top roof seam down to the window frame, then from the window frame to just below the formed portion of the cab, basicly to the cab floor..

[swamp rat]

Here's an inside shot of the ceiling, sorry about the sideways pic.... Definitely would like enough overlap that i can do some flanging work all the way around the opening inside and out. I want the inside panel intact at the joint above the dome light.

[swamp rat]

I'm not an artist... LOL I have no idea how much shipping would be for a piece the size as the bottom, don't even know if its worth trying to ship. I am assuming that any rust on the inside of the panels is surface only being from Arizona..

[jmedero]

Payment sent for wiper motor mount. Thanks.

[t korinek]

Here's the piece for 6t727t2, looks good inside & out, only surface rust inside.

All of these Cabs have some rust in the bottom of the kick panel crevice, where it meets the floor, the 67 cab looked promising, but it has been repaired previously, If your ok with some rust, let me know

Swamp rat, Back of the 67 cab looks good, nothing more than some surface rust, I'll sell that section for $60 but shipping could be the problem, have a business addy it could ship to?

Ol 67 C10 contact member pat english he has the front of frame horns you were looking for

[t korinek]

Another of the inside of the 67 cab

[6t727t2]

Tom, cowl pp looks good, pm sent with shipping info

[67chevy4x4c]

I am interested in the kick panel if the rust is only about 4 to 5 inchs up on the 67 cab is the inter cowl good on the 67 I need about 15 inchs of it were it ties in to the kick panel let me know if it is fair I would like to buy it. Thanks

[t korinek]

67chevy4x4c is this what your talking about?