![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
![]() Join Date: Jan 2015
Location: usa
Posts: 335
|
rag or universal joint
getting ready to do a power steering set up on 65 c10,Ive seen rag joint on most but also universal on some ,any thoughts on this?
|
![]() |
![]() |
![]() |
#2 |
Never Ending Projects
Join Date: Jul 2006
Location: San Diego, CA
Posts: 3,836
|
Re: rag or universal joint
Depends on your steering column hook up. If reusing a factory setup, you're likely going to use a rag joint. If aftermarket column that is spline, you'll use a u-joint setup. Either works. Rag joint take a little of the vibration out of the steering wheel but has a slightly softer feel versus a u-joint setup which is very direct.
__________________
. 1965 C10 Panel, ![]() 1968 Chevy C10, Long, Fleetside, Hot Rod Hauler http://67-72chevytrucks.com/vboard/s...d.php?t=313233 SOLD 1965 Chevy C10, Long, Fleetside, Hot Rod C10 http://67-72chevytrucks.com/vboard/s...d.php?t=415702 SOLD We were given two ears and one mouth for a reason... listen twice as much and speak half as often... |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Nov 2011
Location: Chaparral NM
Posts: 693
|
Re: rag or universal joint
What chevy_mike says.. Will need to know how many splines are on your gear box you will have to match it up on the rag joint. Usually the universal joint depending on whats on the end of the steering column splined or OD end will fit the collapsable steering shaft. It was alot simpler and cheaper to but the whole kit from CPP. Here is a pic...
__________________
CURRENT & PAST CHEVY TRUCKS 60 C-10 Apache short step side 62 C-10 short step side 66 GMC Long bed fleet side 305 V-6 77 C-20 Custom Deluxe (Blue Goose) |
![]() |
![]() |
![]() |
#4 |
Senior Enthusiast
Join Date: Feb 2007
Location: Spokane Valley, WA
Posts: 8,356
|
Re: rag or universal joint
Mine looks like the picture above. The rag joint and shaft is a $5.00 assembly from a 78-80 Monte Carlo. I cut off the factory u-joint at the top and installed a polished stainless Borgeson joint when I swapped to a chrome Ididit column:
![]()
__________________
My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=444502 |
![]() |
![]() |
![]() |
#5 | |
Registered User
Join Date: Jan 2009
Location: Burbank, CA
Posts: 3,610
|
Re: rag or universal joint
Quote:
|
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Nov 2010
Location: Indiana, PA
Posts: 220
|
Re: rag or universal joint
I am hoping for the best of both worlds. On my build I used a vibration reducing u-joint by Borgeson along with a collapsible shaft and a regular u-joint on the other end. Now if I just had the paint finished and I could drive it...
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Nov 2011
Location: Chaparral NM
Posts: 693
|
Re: rag or universal joint
Installed it so it can collapse. shaft goes in far and still has adjustment. It also makes it more easier to install...here is another pic..
__________________
CURRENT & PAST CHEVY TRUCKS 60 C-10 Apache short step side 62 C-10 short step side 66 GMC Long bed fleet side 305 V-6 77 C-20 Custom Deluxe (Blue Goose) Last edited by doobiebro; 03-12-2015 at 10:04 AM. |
![]() |
![]() |
![]() |
Bookmarks |
|
|