|
03-21-2015, 02:31 PM
|
#1 |
|
Registered User
Join Date: Jan 2013
Location: San Antonio, TX
Posts: 733
|
stock gurus' question
Is the body side moulding on this stock?
http://sanantonio.craigslist.org/cto/4903541330.html
__________________
Figure out what you want--then figure out what you are willing to give up to get it. |
|
|
|
03-21-2015, 02:34 PM
|
#2 |
|
Senior Member
 
Join Date: Oct 2009
Location: Godley, TX
Posts: 17,945
|
Re: stock gurus' question
Yep
|
|
|
|
|
03-21-2015, 02:45 PM
|
#3 |
|
C/10 junkie
Join Date: Nov 2010
Location: Stockton Ca
Posts: 9,093
|
Re: stock gurus' question
Yes but odd to see without th lower trim in place as well
__________________
Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!" 
|
|
|
|
|
03-21-2015, 03:21 PM
|
#4 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,862
|
Re: stock gurus' question
Could be, but could have been added, too. I see the mirrors were replaced and don't see holes from originals. Upper only could be ordered, though
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
03-21-2015, 03:26 PM
|
#5 | |
|
Registered User
Join Date: Jan 2013
Location: San Antonio, TX
Posts: 733
|
Re: stock gurus' question
Quote:
__________________
Figure out what you want--then figure out what you are willing to give up to get it. |
|
|
|
|
|
03-21-2015, 04:12 PM
|
#6 | ||
|
Registered User
Join Date: Nov 2009
Location: Sherman, ME
Posts: 2,359
|
Re: stock gurus' question
Quote:
RPO B85 is described in the info kit from the GM Heritage Center as follows: Quote:
|
||
|
|
|
|
03-21-2015, 04:29 PM
|
#7 | |
|
Registered User
Join Date: Aug 2010
Location: Edwards, CA
Posts: 7,503
|
Re: stock gurus' question
Quote:
This truck appears to be Custom/10 (base trim) and as such it would be listed on the SPID if original to the truck. However the tailgate should also have the upper and lower moldings. http://67-72chevytrucks.com/vboard/s...d.php?t=572206
__________________
Thanks, Tim * VIN/Model Decoders * Power Team Charts (engine/transmission/gear ratio) * Post Your Pickup SPID ** Blazer SPID ** Suburban/Panel SPID * RTFM ... Read The Factory Manuals... download 'em here Highlanders ** Do you have a 1972 Plaid Pickup? ** Plaid Blazer ** Plaid Suburban |
|
|
|
|
|
03-21-2015, 04:55 PM
|
#8 |
|
Registered User
Join Date: Jan 2013
Location: San Antonio, TX
Posts: 733
|
Re: stock gurus' question
Thanks guys. You guys are tops. May go check it out. Sure need a fleetside to go with my stepper...
__________________
Figure out what you want--then figure out what you are willing to give up to get it. |
|
|
|
|
03-21-2015, 08:34 PM
|
#9 |
|
Senior Member
Join Date: Aug 2011
Location: Benton, AR.
Posts: 239
|
Re: stock gurus' question
Here's another example of B85 upper belt molding only on my Longhorn.
__________________
Tony 1972 Chevy K10 SWB Custom Deluxe 350|350|NP205 2018 GMC Sierra Z/71 Crew 2008 GMC Yukon 2007 Chevy 1500 LT 1967 Pontiac Firebird 400 |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
