|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
04-08-2015, 09:35 AM
|
#1 |
|
Registered User
Join Date: Jul 2009
Location: watertown, tn
Posts: 332
|
p/s mounting w/ headers....how to?
I have a '71 c10 that i drag race exclusivley that has oem p/s with long water pump brackets, trying to figure out how to mount the pump. I have the oem cradle the pump sits in and the slotted adjuster bracket with three holes that mounts to the front of the pump, but dont have the one piece that attaches to the exhaust manifold bolt. Dont even know if it would help if i had it because im running long tube headers? Anyone else run into this problem or know how to remedy it?
__________________
'71 LWB c10-"WORK" in progress  385 ci 4 bolt (4.040 bore), scat 6.0" forged h beams,scat forged crank 3.750, speed pro 5cc flat top, clevite bearings, .039 head gaskets,comp xr288hr 110* 288/294adv. 236/242@.50 555/576 lift, pbm hyd roller lifters, chad spiers 215cc imp. heads , comp 1.6 roler rockers, comp magnum push rods, edelbrock victor jr. single plane intake p&p (1206 gasket matched), quickfuel 750R DP , th 350 trans, 5.14 gear, 3000 stall 2012 best 1/8- 7.70 @ 87mph 1.70 60' (lil better) 2013 best 7.39 2014 best-7.38 New for 2013-strange rear coilovers, headman 1-3/4 headers, 5.13 r&p, .060 aluminum bed floor, 15x14 holeshots w/ 31x18.5 hoosier dot pro's, 15x4 holeshots w/ 26x5.5 m/t skinnies and 200+#'s in body weight loss & 6 point cage |
|
|
|
04-08-2015, 09:48 AM
|
#2 |
|
Senior Member
 
Join Date: Mar 2012
Location: Chesapeake, Va
Posts: 1,275
|
Re: p/s mounting w/ headers....how to?
Not for sure if it matters on the Long Water pump, but my bracket runs over to the Motor mount not the header, maybe you can find one of those , I run a short water pump,
I do not know if there are two different brackets for a LWP or SWP??
__________________
Mike 72 C-10 Cheyenne off frame resto and Upgraded to 4 wheel disk, Tilt, Dakota Digital Dash / Rear slider. 421 SBC / TH350 3000RPM Stall Progression Ignition /Holley 750 DP/3:73 gear Eaton Limited Slip unit / 2 1/2 exhaust glasspacks 
|
|
|
|
|
04-08-2015, 05:24 PM
|
#3 |
|
Registered User
Join Date: Apr 2013
Location: South Westerlo, New York
Posts: 1,325
|
Re: p/s mounting w/ headers....how to?
Or, you could go to manual steering since you just go in a straight line and pick up a few more horses...
__________________
Thanks, Joe.. 1969 C/10, 348 C.I., 3X2 bbl. V8, 2004r , LWB. |
|
|
|
|
04-09-2015, 11:06 AM
|
#4 |
|
Registered User
Join Date: Jul 2009
Location: watertown, tn
Posts: 332
|
Re: p/s mounting w/ headers....how to?
Thought about that to hamjet but these trucks are hard as hell to turn w/ no P/S, all that weight i guess.
__________________
'71 LWB c10-"WORK" in progress 385 ci 4 bolt (4.040 bore), scat 6.0" forged h beams,scat forged crank 3.750, speed pro 5cc flat top, clevite bearings, .039 head gaskets,comp xr288hr 110* 288/294adv. 236/242@.50 555/576 lift, pbm hyd roller lifters, chad spiers 215cc imp. heads , comp 1.6 roler rockers, comp magnum push rods, edelbrock victor jr. single plane intake p&p (1206 gasket matched), quickfuel 750R DP , th 350 trans, 5.14 gear, 3000 stall 2012 best 1/8- 7.70 @ 87mph 1.70 60' (lil better) 2013 best 7.39 2014 best-7.38 New for 2013-strange rear coilovers, headman 1-3/4 headers, 5.13 r&p, .060 aluminum bed floor, 15x14 holeshots w/ 31x18.5 hoosier dot pro's, 15x4 holeshots w/ 26x5.5 m/t skinnies and 200+#'s in body weight loss & 6 point cage |
|
|
|
|
04-09-2015, 11:23 AM
|
#5 | |
|
Registered User
Join Date: May 2011
Location: Oakley, Michigan
Posts: 735
|
Re: p/s mounting w/ headers....how to?
Quote:
|
|
|
|
|
|
04-09-2015, 11:43 AM
|
#6 |
|
Registered User
Join Date: Dec 2012
Location: Chandler AZ
Posts: 1,149
|
Re: p/s mounting w/ headers....how to?
One could easily fab a bracket that went from motor mount to stud in the back of the pump out of ½" steel tubing. The rear stud on mine is far away from the headers.
The SWP mount I have doesn't have a rear mount. It is a cradle type. Sorry I don't have a better pic.
__________________
1970 Longhorn, Front Disc, 350/4 bolt, 882 heads, HEI, Edelbrock, 700R4, HO-52/4.11. 1996 Corvette, Collector Roadster, LT4, 396, 450RWHP, 6sp, 4.11/Dana44/posi 5 point roll bar And let us not grow weary of doing good, for in due season we will reap, if we do not give up. Gal 6:9 |
|
|
|
|
04-09-2015, 12:00 PM
|
#7 |
|
Registered User
Join Date: Jul 2009
Location: watertown, tn
Posts: 332
|
Re: p/s mounting w/ headers....how to?
BrianG I didnt realize that a manual box would be easier to turn than a power unit thats not working. I wounder what all a person would have to change to utilize a manual box.....linkages and otherwise?
__________________
'71 LWB c10-"WORK" in progress 385 ci 4 bolt (4.040 bore), scat 6.0" forged h beams,scat forged crank 3.750, speed pro 5cc flat top, clevite bearings, .039 head gaskets,comp xr288hr 110* 288/294adv. 236/242@.50 555/576 lift, pbm hyd roller lifters, chad spiers 215cc imp. heads , comp 1.6 roler rockers, comp magnum push rods, edelbrock victor jr. single plane intake p&p (1206 gasket matched), quickfuel 750R DP , th 350 trans, 5.14 gear, 3000 stall 2012 best 1/8- 7.70 @ 87mph 1.70 60' (lil better) 2013 best 7.39 2014 best-7.38 New for 2013-strange rear coilovers, headman 1-3/4 headers, 5.13 r&p, .060 aluminum bed floor, 15x14 holeshots w/ 31x18.5 hoosier dot pro's, 15x4 holeshots w/ 26x5.5 m/t skinnies and 200+#'s in body weight loss & 6 point cage |
|
|
|
|
04-09-2015, 12:06 PM
|
#8 | |
|
Registered User
Join Date: May 2011
Location: Oakley, Michigan
Posts: 735
|
Re: p/s mounting w/ headers....how to?
Quote:
As far as what is needed, I'm sure that other members would be able to give a more accurate response. You might find someone who would be willing to do a swap. |
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
