C.L. '69 C10 LS project $2k obo - The 1947 - Present Chevrolet & GMC Truck Message Board Network

RustyBucket · 07-07-2015, 02:47 PM

http://spacecoast.craigslist.org/cto/5105244250.html

not me but interesting

Aruba1 · 07-07-2015, 02:55 PM

Offer $1500 and go get her. If the 6.0 turns out fine you would have done really well. A 6.0 is at least a $1000 engine all day long, some go for $1500 and up. The NV4500 is at least $600. Clutch and special flywheel (depending which flywheel was used) will set you another $500 minimum. I would be interested to find if the driveshaft is hooked up, that will save you $200 to have it shortened and balanced. You will still need a harness (if he does not have one) that will run you about $600. I just finished doing my conversion (5.3L with NV4500) and I have about $1800 in the engine and engine parts alone, not counting the transmission and driveshaft shortened.

67 chevelle · 07-07-2015, 03:00 PM

sounds like a deal , but anyone can dump a non running ls "in the hole" ,of a very ruff truck ,, thats a whole lot of "project" , like everything.
Looks like the guy pulled out the sb and thew it in there from quiet a distance

hugger6933 · 07-07-2015, 03:24 PM

Well if the motor wasn't wired it most likely wouldn't have the UBEC sitting on the fenderwell. If the drivetrain is good then you would def be ok. jim

boraxman · 07-07-2015, 04:20 PM

Looks like a roll of the dice/

Aruba1 · 07-07-2015, 04:53 PM

Quote:

Originally Posted by boraxman

Looks like a roll of the dice/

And big reward awaiting if the engine turns out good and little reward if the engine is bad. Worst case it's still money to be made if he takes $1500.

dukkie · 07-07-2015, 10:13 PM

Verify by looks alone, is that not the cover of a 4.8/5.3 and NOT a 6.0 ?
am I incorrect?

6.0

indymachinist · 07-07-2015, 10:33 PM

Well an iron headed 6.0 ls engine is older. I believe 99 and 00 only. So that may just be an older style of plastic cover. Nor sure honestly. I am pretty sure the older iron headed 6.0 engine also has a longer crank shaft as it was intended to run with a 4l80e trans only. Later year 6.0 engines used a spacer with the 4l80e instead of a longer crank.

**leddzepp** · 07-07-2015, 10:40 PM

Quote:

Originally Posted by boraxman

Looks like a roll of the dice/

X2. Non running engine = boat anchor.

Aruba1 · 07-07-2015, 11:21 PM

If I am not mistaken the 6.0L did not come with aluminum heads till 2001. The engine cover is for a Vortec 4.8, 5.3 and 6.0 from 1999 to 2002 in the silverado, sierra, tahoe and yukon. I had to ebay Vortec 6.0L engine cover to find out as my 2000 5.3L did not come with one, but these were put in other vehicles too and cover may look different.

71sierragrande · 07-08-2015, 07:28 AM

I had a 2004 escalade with the vortec 6.0. The cover had "VORTEC 6000" printed on it. Strong engine

indymachinist · 07-08-2015, 09:31 AM

Your 04 escalade engine was a better engine than this older one.

Not to say that this one is bad it's just not as powerful.

jackyl9999 · 07-08-2015, 09:41 AM

I am always afraid of "projects". Sometimes there is a reason they stopped working on them.

That truck looks like it has been sitting for awhile.

1500 is the absolute max I would offer. I would offer less.

07-07-2015, 02:47 PM	#1
RustyBucket Registered User Join Date: Jul 2009 Location: Space Coast, Fl. Posts: 1,055	C.L. '69 C10 LS project $2k obo http://spacecoast.craigslist.org/cto/5105244250.html not me but interesting __________________ Dad always said, "Son, WISH IN ONE HAND, and ......." -------------------------------------- -------------------------------------- Current toy trucks: '71 GMC 1500 SUPER CUSTOM short/step, orig. dk. blue, 350/700r, ps,pb, A/C '72 Blazer 2wd, ochre & white, 454, tremecTKO 500 5spd. ps, pb, A/C, tilt Last 10yrs of hobby vehicles, had a FEW more in the 50yrs. before these: '66 Plymouth Belvedere City of Miami cop car clone. '70 Nova 406"sb, 13.5-1, solid roller, Brodix, p.glide/t.brake, back halved, 9" Ford, spool 4.88, cage,ladder bar/coilover, 10.5 tire....... SOLD!! '67 C10 short/step side mount spare -- SOLD!! '72 Jimmy 2wd, 350/350, ps, pb, fun driver, lots of bondo & a shiny red paint job..... SOLD!! '69 Nova 350, 4spd, A/C, ps, p.b, ...SOLD!!

07-07-2015, 02:55 PM	#2
Aruba1 Registered User Join Date: Apr 2014 Location: Birmingham, AL Posts: 560	Re: C.L. '69 C10 LS project $2k obo Offer $1500 and go get her. If the 6.0 turns out fine you would have done really well. A 6.0 is at least a $1000 engine all day long, some go for $1500 and up. The NV4500 is at least $600. Clutch and special flywheel (depending which flywheel was used) will set you another $500 minimum. I would be interested to find if the driveshaft is hooked up, that will save you $200 to have it shortened and balanced. You will still need a harness (if he does not have one) that will run you about $600. I just finished doing my conversion (5.3L with NV4500) and I have about $1800 in the engine and engine parts alone, not counting the transmission and driveshaft shortened.

07-07-2015, 03:00 PM	#3
67 chevelle Registered User Join Date: May 2013 Location: WEST PALM FLORIDA Posts: 1,174	Re: C.L. '69 C10 LS project $2k obo sounds like a deal , but anyone can dump a non running ls "in the hole" ,of a very ruff truck ,, thats a whole lot of "project" , like everything. Looks like the guy pulled out the sb and thew it in there from quiet a distance __________________ 68 Long Fleet , ly6 , turbo 350 , 3-5 drop , original paint , front discs 67 Small window , 7 foot bed , tweaked 6.0 LSX 2004R Medium Olive 58 Apache fleet , 235 , offy intake , dual exhaust , 4 on the floor , red/white 69 Long Fleet , Custom , 6.0, 4l60 , AC , Medium Olive

07-07-2015, 03:24 PM	#4
hugger6933 Registered User Join Date: Oct 2008 Location: Marianna Arkansas Posts: 7,280	Re: C.L. '69 C10 LS project $2k obo Well if the motor wasn't wired it most likely wouldn't have the UBEC sitting on the fenderwell. If the drivetrain is good then you would def be ok. jim

07-07-2015, 04:20 PM	#5
boraxman Keepin an eye out Join Date: Feb 2003 Location: So.Cal Posts: 3,920	Re: C.L. '69 C10 LS project $2k obo Looks like a roll of the dice/ __________________ 1970 Chevy C10 SWB 5.3 1996 Toyota Tacoma SR5 4x4 2007 Vespa GTS 250 Scooter ZIP 91351

07-07-2015, 10:13 PM	#7
dukkie My Spoon Is Too Big Join Date: Mar 2010 Location: Magnolia Tx Posts: 457	Re: C.L. '69 C10 LS project $2k obo Verify by looks alone, is that not the cover of a 4.8/5.3 and NOT a 6.0 ? am I incorrect? 6.0 __________________ 1972 C20, 03-14-10 Build Thread 2000 Silverado 4.8L, 11-04-13 (Currently Parting) 1999 Silverado 5.3L, 07-07-14. (Engine Donor) 2015 Ram 05-20-15 (Daily Driver) Last edited by dukkie; 07-07-2015 at 10:21 PM.

07-07-2015, 10:33 PM	#8
indymachinist Registered User Join Date: Jun 2015 Location: Indanapolis, IN Posts: 603	Re: C.L. '69 C10 LS project $2k obo Well an iron headed 6.0 ls engine is older. I believe 99 and 00 only. So that may just be an older style of plastic cover. Nor sure honestly. I am pretty sure the older iron headed 6.0 engine also has a longer crank shaft as it was intended to run with a 4l80e trans only. Later year 6.0 engines used a spacer with the 4l80e instead of a longer crank.

07-07-2015, 11:21 PM	#10
Aruba1 Registered User Join Date: Apr 2014 Location: Birmingham, AL Posts: 560	Re: C.L. '69 C10 LS project $2k obo If I am not mistaken the 6.0L did not come with aluminum heads till 2001. The engine cover is for a Vortec 4.8, 5.3 and 6.0 from 1999 to 2002 in the silverado, sierra, tahoe and yukon. I had to ebay Vortec 6.0L engine cover to find out as my 2000 5.3L did not come with one, but these were put in other vehicles too and cover may look different.

07-08-2015, 07:28 AM	#11
71sierragrande Petroleum User Join Date: Dec 2010 Location: San Diego, California Posts: 928	Re: C.L. '69 C10 LS project $2k obo I had a 2004 escalade with the vortec 6.0. The cover had "VORTEC 6000" printed on it. Strong engine __________________ 1971 GMC Sierra Grande 2WD 1/2 ton, 350/400 auto 2008 Chevy Silverado 2WD 1/2 ton LT1 5.3L auto

07-08-2015, 09:31 AM	#12
indymachinist Registered User Join Date: Jun 2015 Location: Indanapolis, IN Posts: 603	Re: C.L. '69 C10 LS project $2k obo Your 04 escalade engine was a better engine than this older one. Not to say that this one is bad it's just not as powerful.

07-08-2015, 09:41 AM	#13
jackyl9999 Registered User Join Date: Feb 2003 Location: Paragould, Ar Posts: 571	Re: C.L. '69 C10 LS project $2k obo I am always afraid of "projects". Sometimes there is a reason they stopped working on them. That truck looks like it has been sitting for awhile. 1500 is the absolute max I would offer. I would offer less. __________________ 1970 Gmc Grande Sierra Swb 2wd LSX (LQ4/4L80e) 1990 K1500 Daily



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.