|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
10-10-2015, 02:51 PM
|
#1 |
|
Registered User
Join Date: Jun 2014
Location: Connecticut
Posts: 521
|
Transfer case shifter pivot bushing?
 The shifter on the T221 in my '65 K10 is loose. In particular it slides side-to-side, and generally rattles. I'm assuming at this point there are rubber (or other) bushings missing from the pivot shaft, which is allowing for all this movement and the resulting rattle. Is there a source for pieces like this or am I going to have to make something up? |
|
|
|
10-10-2015, 03:15 PM
|
#2 |
|
Registered User
Join Date: Feb 2012
Location: pleasant valley--placerville ca
Posts: 3,039
|
Re: Transfer case shifter pivot bushing?
there is a spring that goes between the shifter and the mounting bracket. It keeps the shifter against the outer c-clip.
__________________
1961 chevy K10 my build is------------61K10 build |
|
|
|
|
10-10-2015, 06:53 PM
|
#3 | |
|
Registered User
Join Date: Jun 2014
Location: Connecticut
Posts: 521
|
Re: Transfer case shifter pivot bushing?
Quote:
|
|
|
|
|
|
10-11-2015, 12:50 PM
|
#4 |
|
Registered User
Join Date: Feb 2012
Location: pleasant valley--placerville ca
Posts: 3,039
|
Re: Transfer case shifter pivot bushing?
no a small coil type spring, but the spring washer might work. maybe 2? A lite wait spring from a hardware store--cut a few coils off--should work.
__________________
1961 chevy K10 my build is------------61K10 build |
|
|
|
|
10-12-2015, 12:14 AM
|
#5 |
|
Registered User
Join Date: Sep 2008
Location: San Carlos, Ca.
Posts: 3,048
|
Re: Transfer case shifter pivot bushing?
Thats funny, mine is welded to the hump. Thought they came like that. Damn, another thing to fix now.
__________________
Chris '63 k15 long step Vortec 7.4 - L29 Blackbear tune, Five 0 Motorsports injectors, Chris Straub Cam, NV4500, divorced 205  52" front and 63" rear spring swap D44 / 14bff - disc axles Milemarker 9K and 10.5K hydraulic winches 63" & B52 Spring Install http://67-72chevytrucks.com/vboard/s...ng+swap+thread NV4500 Reverse Build Thread http://67-72chevytrucks.com/vboard/s...=reverse+build L29 - 7.4 Vortec Build http://67-72chevytrucks.com/vboard/s...&highlight=L29 |
|
|
|
|
10-12-2015, 11:53 AM
|
#6 | |
|
Registered User
Join Date: Jun 2014
Location: Connecticut
Posts: 521
|
Re: Transfer case shifter pivot bushing?
Quote:
|
|
|
|
|
|
10-12-2015, 12:19 PM
|
#7 |
|
Registered User
Join Date: Feb 2012
Location: pleasant valley--placerville ca
Posts: 3,039
|
Re: Transfer case shifter pivot bushing?
Jimal--there was none on mine. Diagram for adjusting linkage doesn't show any.
63GEN---welded to the hump?
__________________
1961 chevy K10 my build is------------61K10 build Last edited by 61K10; 10-12-2015 at 12:26 PM. |
|
|
|
|
10-13-2015, 02:05 PM
|
#8 | |
|
Registered User
Join Date: Jun 2014
Location: Connecticut
Posts: 521
|
Re: Transfer case shifter pivot bushing?
Quote:
|
|
|
|
|
|
10-14-2015, 12:03 PM
|
#9 |
|
Registered User
Join Date: Feb 2012
Location: pleasant valley--placerville ca
Posts: 3,039
|
Re: Transfer case shifter pivot bushing?
i replaced all the pins in the linkage with bolts with lock nuts to get rid of most of the slop.
__________________
1961 chevy K10 my build is------------61K10 build |
|
|
|
|
10-18-2015, 01:40 AM
|
#10 |
|
Registered User
Join Date: Mar 2010
Location: Edgewater NJ
Posts: 159
|
Re: Transfer case shifter pivot bushing?
I put all new pins in my linkage as well. In addition, wherever I could, I drilled out the linkage to 1/2" and pressed in 1/2" x 3/8" bushings. This took care of most of the slop and rattling.
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
