|
02-22-2004, 08:11 PM
|
#1 |
|
Registered User
Join Date: Mar 2003
Location: Walker, LA
Posts: 2,925
|
Attn: Ocbaud
Hey Eric, which mufflers are you gonna run on it? You may want to drop another $50 and put some cut-outs on it.
__________________
Gary -1986 SWB: lowered 4/6, SOLD!!! -Best 1/4 mile: 14.51 @ 91.01 MPH -2001 Pewter Tahoe, billet grill, Corsa Sport Cat-back, K&N FIPK SOLD!!! -2004 Z-71 Extended cab with a flowmaster, BDS 6.5", 3" BL, 35x12.5x18 Trail Grapplers on Pro-Comp 18x9 wheels |
|
|
|
02-23-2004, 12:44 AM
|
#2 |
|
Registered User
Join Date: Mar 2003
Location: Walker, LA
Posts: 2,925
|
ttt
__________________
Gary -1986 SWB: lowered 4/6, SOLD!!! -Best 1/4 mile: 14.51 @ 91.01 MPH -2001 Pewter Tahoe, billet grill, Corsa Sport Cat-back, K&N FIPK SOLD!!! -2004 Z-71 Extended cab with a flowmaster, BDS 6.5", 3" BL, 35x12.5x18 Trail Grapplers on Pro-Comp 18x9 wheels |
|
|
|
|
02-23-2004, 12:52 AM
|
#3 |
|
yeller
Join Date: Oct 2001
Location: Twin Cities
Posts: 13,826
|
I ran cut-outs on mine, but they turned out to be a PITA. You need to mount them as close to the header as possible (lowest spot on the exhaust too), and since they hang down...they scraped quite a bit. It was cool uncorking the exhaust though...especially during the burnout contest....maaan was it loud!
__________________
Jeff 73-87.com 73-87.com Facebook page 73-87 cab corner 6x9 speaker brackets for sale 67-72 cab corner speaker brackets for sale 47-54 cab corner speaker brackets for sale |
|
|
|
|
02-23-2004, 12:52 AM
|
#4 |
|
Garage Queen Material
Join Date: Oct 2002
Location: USA
Posts: 4,129
|
i'll keep the flows on it for a while. after i get the engine started up and running good, i'll have to take it to the exhaust shop and have him extend the pipes to reach the shortie headers i'll have. cut outs would be cool for the strip though
|
|
|
|
|
02-23-2004, 01:06 AM
|
#5 |
|
Registered User
Join Date: Mar 2003
Location: Walker, LA
Posts: 2,925
|
Clearance with a 4/6 drop and full lengths.
__________________
Gary -1986 SWB: lowered 4/6, SOLD!!! -Best 1/4 mile: 14.51 @ 91.01 MPH -2001 Pewter Tahoe, billet grill, Corsa Sport Cat-back, K&N FIPK SOLD!!! -2004 Z-71 Extended cab with a flowmaster, BDS 6.5", 3" BL, 35x12.5x18 Trail Grapplers on Pro-Comp 18x9 wheels |
|
|
|
|
02-23-2004, 11:28 AM
|
#6 |
|
BeWarE tHe eViL CrAnkTOe!
Join Date: Oct 2002
Location: Yukon, OK
Posts: 3,605
|
Depends on what full lengths and what tire/wheel combo you run. My full lengths were HOrribly close to the ground. on a 4/6 with 16's and 50 series tires.
__________________
~Dave~ You can call me Mike, Mike Oxlong - 1986 Chevy SWB - Stock for now - 1986 Chevy Custom SWB *Stolen 6/26/05* - 1985 Chevy SWB SOLD - 1999 T/A Some mods  www.cardomain.com/id/ramairdave AIM Screenname - Jester84 |
|
|
|
|
02-23-2004, 12:38 PM
|
#7 |
|
Registered User
Join Date: Sep 2003
Location: Lewisville, NC
Posts: 1,836
|
I just about took the collectors off my 83 GMC 2wd longbed once. Of course I was going up a rough road in the mountains. But it had stock suspensions and 225/75R15 in front and 235/75 in the back. But the passenger side exhaust hung down quite low because I had it run below the crossmember. Just about took the cats off with it too hehe.
__________________
1985 Scottsdale Shortbed 4x4 Stout 350 with some "upgrades"-700r4-33x12.5" Mud Tires, Warn 8274-50 winch. 2005 Chevrolet Colorado Regular Cab 2wd 4-banger, 5 speed, Street Pack with 3.73 axle. |
|
|
|
|
02-23-2004, 01:24 PM
|
#8 | |
|
Trucker.
Join Date: Nov 2002
Location: Fort Worth, TX
Posts: 1,364
|
Quote:
BTW those will be getting replaced by some 18's in a week and get retired so they can be fully polished.
|
|
|
|
|
|
02-23-2004, 01:28 PM
|
#9 | |
|
Registered User
Join Date: Mar 2003
Location: Walker, LA
Posts: 2,925
|
Quote:
__________________
Gary -1986 SWB: lowered 4/6, SOLD!!! -Best 1/4 mile: 14.51 @ 91.01 MPH -2001 Pewter Tahoe, billet grill, Corsa Sport Cat-back, K&N FIPK SOLD!!! -2004 Z-71 Extended cab with a flowmaster, BDS 6.5", 3" BL, 35x12.5x18 Trail Grapplers on Pro-Comp 18x9 wheels |
|
|
|
|
|
02-23-2004, 02:49 PM
|
#10 |
|
Garage Queen Material
Join Date: Oct 2002
Location: USA
Posts: 4,129
|
well, i'll be running 255/45/17s in the front. if electric cutouts werent so expensive i would get them
|
|
|
|
|
02-23-2004, 03:06 PM
|
#11 |
|
Hotwheels?
Join Date: Dec 2002
Location: Pleasant Hill, CA
Posts: 1,145
|
Elecrtic cutouts are so awesome. Im seriously considering getting them. It'd be about 350 for 2. It would be more for show though...
__________________
1978 Money Pit - CUSTOM DELUXE!!!! |
|
|
|
|
02-23-2004, 04:12 PM
|
#12 |
|
Registered User
Join Date: Oct 2002
Location: Edmond, OK
Posts: 5,906
|
cable actuated cutouts wouldnt be that bad...
__________________
Jon 1982 Chevy Silverado 350/th350.... RETIRED 1993 Jeep XJ 2 door(Cherokee) 4wd 4.0ltr/AX-15 (5spd)/NP231 .... Oklahoma Roll Call |
|
|
|
|
02-23-2004, 05:24 PM
|
#13 |
|
Hotwheels?
Join Date: Dec 2002
Location: Pleasant Hill, CA
Posts: 1,145
|
Cable cutouts need to be custom made... and they rust up and jam after the first rain. Its a cool concept, but doesnt really work out. Regular cutouts seem to be a pain for a daily driver too. F-Body guys go nuts over the Electric ones, they are really reliable and just plain cool to boot.
__________________
1978 Money Pit - CUSTOM DELUXE!!!! |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
