Weird "bucking" issue - The 1947 - Present Chevrolet & GMC Truck Message Board Network

kaysboat · 03-14-2016, 06:54 AM

I'm starting to have an intermittent (although more frequent) "bucking" issue with my 1980 C10. (250 straight six, three on the tree). Initially when I start driving it drives very smooth and normal. Sometimes after 5-10 minutes I start getting a relatively major shaking/shimmy through what feels like the drive line. (When I engage the clutch and rev the engine engine is smooth and sounds normal, although shaking continues).

The shaking inceases and decreases with associated speed changes. Usually I pull over for a minute (leaving the truck running), then the problem almost always fixes itself. Sometimes it is fine for the remainder of the drive, sometimes the issue starts again in a few minutes.

I just had the clutch replaced in the fall, and had the flywheel machined at that time. The only issue I can see currently with the truck is a small hole in the exhaust pipe (about the size of a dime) just in front of the muffler (have to get that fixed up soon). Although I doubt that would cause such an issue, but I'm not sure. All wheel weights are still on the wheels (although I don't see how a wheel weight flying off would cause an intermittent issue).

Any thoughts?

'76 Big Block · 03-14-2016, 08:17 AM

Was the throw-out bearing replaced when the clutch was replaced?
How much free play do you have before the clutch engages?
The shaking with the clutch engaged indicates clutch/bearing issues (to me)----good luck!

kaysboat · 03-14-2016, 08:42 AM

The throw out bearing was replaced
I meant to say "disengage the clutch" and rev the engine. Engine runs smooth even with the clutch disengaged, but shaking persists.

geezer#99 · 03-14-2016, 09:07 AM

Sounds like your heat riser is stuck or not working and you have a cold intake plenum.
How long do you let it warm up before you drive away?

kaysboat · 03-14-2016, 11:55 AM

I usually let it warm up for 2-5 minutes. Basically once it no longer would stall without giving it a bit of gas.

geezer#99 · 03-14-2016, 12:19 PM

Is your motor all stock?
Is it an integral head motor?
After you stop and sit a bit and it fixes itself, does it run much better after that with no bucking sensation?

03-14-2016, 06:54 AM	#1
kaysboat Registered User Join Date: Jul 2013 Location: Nova Scotia Posts: 27	Weird "bucking" issue I'm starting to have an intermittent (although more frequent) "bucking" issue with my 1980 C10. (250 straight six, three on the tree). Initially when I start driving it drives very smooth and normal. Sometimes after 5-10 minutes I start getting a relatively major shaking/shimmy through what feels like the drive line. (When I engage the clutch and rev the engine engine is smooth and sounds normal, although shaking continues). The shaking inceases and decreases with associated speed changes. Usually I pull over for a minute (leaving the truck running), then the problem almost always fixes itself. Sometimes it is fine for the remainder of the drive, sometimes the issue starts again in a few minutes. I just had the clutch replaced in the fall, and had the flywheel machined at that time. The only issue I can see currently with the truck is a small hole in the exhaust pipe (about the size of a dime) just in front of the muffler (have to get that fixed up soon). Although I doubt that would cause such an issue, but I'm not sure. All wheel weights are still on the wheels (although I don't see how a wheel weight flying off would cause an intermittent issue). Any thoughts?

03-14-2016, 08:17 AM	#2
'76 Big Block Registered User Join Date: Aug 2011 Location: Rockport, Tx. Posts: 79	Re: Weird "bucking" issue Was the throw-out bearing replaced when the clutch was replaced? How much free play do you have before the clutch engages? The shaking with the clutch engaged indicates clutch/bearing issues (to me)----good luck!

03-14-2016, 08:42 AM	#3
kaysboat Registered User Join Date: Jul 2013 Location: Nova Scotia Posts: 27	Re: Weird "bucking" issue The throw out bearing was replaced I meant to say "disengage the clutch" and rev the engine. Engine runs smooth even with the clutch disengaged, but shaking persists.

03-14-2016, 09:07 AM	#4
geezer#99 Registered User Join Date: Aug 2009 Location: Bowser Posts: 13,731	Re: Weird "bucking" issue Sounds like your heat riser is stuck or not working and you have a cold intake plenum. How long do you let it warm up before you drive away?

03-14-2016, 11:55 AM	#5
kaysboat Registered User Join Date: Jul 2013 Location: Nova Scotia Posts: 27	Re: Weird "bucking" issue I usually let it warm up for 2-5 minutes. Basically once it no longer would stall without giving it a bit of gas.

03-14-2016, 12:19 PM	#6
geezer#99 Registered User Join Date: Aug 2009 Location: Bowser Posts: 13,731	Re: Weird "bucking" issue Is your motor all stock? Is it an integral head motor? After you stop and sit a bit and it fixes itself, does it run much better after that with no bucking sensation?



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.