|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
06-12-2016, 02:02 PM
|
#1 |
|
Registered User
Join Date: Apr 2014
Location: calgary alberta
Posts: 1,248
|
now that it is almost done
i am looking for honest opinions on the truck i have created .
now remember the 69 was a very bad resto that i bought a lot of bondo and spray foam and metal tape so i wasn't cutting up a original truck. the blazer i used was rusted out too. so remember that with your opinion the truck has all new sheet metal the paint is all beat up new paint just beat up to look old this is not a trailer queen lol. here are some pics. |
|
|
|
06-12-2016, 03:31 PM
|
#2 |
|
Registered User
Join Date: Apr 2014
Location: calgary alberta
Posts: 1,248
|
Re: now that it is almost done
here are a few more pics |
|
|
|
|
06-12-2016, 03:37 PM
|
#3 |
|
Registered User
Join Date: Apr 2014
Location: calgary alberta
Posts: 1,248
|
Re: now that it is almost done
some pics of before the cut
|
|
|
|
|
06-12-2016, 04:10 PM
|
#4 |
|
BlahBlahBlah
Join Date: Feb 2002
Location: Wa.
Posts: 19,826
|
Re: now that it is almost done
If its safe and mechanically sound I think your good to go. Might think about putting a bed floor in it haha! Drive and enjoy, do up grades when and if you get the itch.
__________________
… … … … … … … … ... … … … … … … … … … … … |
|
|
|
|
06-12-2016, 05:17 PM
|
#5 |
|
Registered User
 
Join Date: Feb 2016
Location: Weatherford Texas
Posts: 306
|
Re: now that it is almost done
It looks like the driveshaft is a bit short and not allowing the yoke to go deep enough into the trans.
|
|
|
|
|
06-12-2016, 06:46 PM
|
#6 | |
|
Registered User
Join Date: Apr 2014
Location: calgary alberta
Posts: 1,248
|
Re: now that it is almost done
Quote:
|
|
|
|
|
|
06-12-2016, 06:55 PM
|
#7 | |
|
Registered User
Join Date: Apr 2014
Location: calgary alberta
Posts: 1,248
|
Re: now that it is almost done
Quote:
the reason for making the truck is i drive a trans am in the good weather and i needed something to drive to work during our long ass winters up here in canada so this was my way of getting my cake and eating it too. |
|
|
|
|
|
06-12-2016, 06:56 PM
|
#8 |
|
Registered User
Join Date: Apr 2014
Location: calgary alberta
Posts: 1,248
|
Re: now that it is almost done
and i have the bed floor just havent put it in yet still doing fuel lines etc
|
|
|
|
|
06-15-2016, 10:16 PM
|
#9 |
|
Senior Member
Join Date: Jun 2002
Location: Murray, Kentucky
Posts: 3,453
|
Re: now that it is almost done
I dig it. Rg
__________________
Roger '68 Short step - https://67-72chevytrucks.com/vboard/...d.php?t=849675 '69 ('70?) 2wd Blazer '70 GMC Jimmy 2wd '73 Firebird - https://67-72chevytrucks.com/vboard/...d.php?t=853203 |
|
|
|
|
06-16-2016, 12:31 AM
|
#10 |
|
Registered User
Join Date: Jul 2012
Location: Campbell, CA
Posts: 452
|
Re: now that it is almost done
I like it! Nice job. It's all about how fun it is to drive. You can go to car shows to look at ****.
__________________
1971 C/10 - Orange & White 2009 GMC 1500 - Lowered 3/4 22' KMC Slides |
|
|
|
|
06-25-2016, 01:23 AM
|
#11 |
|
Registered User
Join Date: Apr 2014
Location: calgary alberta
Posts: 1,248
|
Re: now that it is almost done
my goal is to have it ready for the last car show of the summer
|
|
|
|
|
07-04-2016, 12:15 AM
|
#12 |
|
Registered User
Join Date: Apr 2014
Location: calgary alberta
Posts: 1,248
|
Re: now that it is almost done
shot the black and metal flake today got tired and hot so i put it out side and took some shots still need some clear and some wet sanding looks good but pics dont give it justice.
|
|
|
|
|
07-04-2016, 12:20 AM
|
#13 |
|
Registered User
Join Date: Apr 2014
Location: calgary alberta
Posts: 1,248
|
Re: now that it is almost done
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
