|
07-09-2016, 09:43 AM
|
#1 |
|
user # 2756
 
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
bench seat question
What year trucks came with a bench seat that does not fold forward? I recently bought a 1986 K30 for parts and the seat is non-folding. I wanted to use it in my 83 but not if I can't fold it forward, looks like the brackets on each side are not factory. i will get some pics today.
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm 
|
|
|
|
07-09-2016, 08:33 PM
|
#2 |
|
user # 2756
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
Re: bench seat question
Driver side bracket.
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm
|
|
|
|
|
07-10-2016, 11:51 AM
|
#3 |
|
Senior Member
Join Date: Oct 2014
Location: Ohio
Posts: 6,980
|
Re: bench seat question
It should fold. it might be because the bolt is not installed. The lower part of the bracket should be bolted to the lower seat bottom. And also the plastic covers are missing that cover the seat bracket.
|
|
|
|
|
07-10-2016, 02:05 PM
|
#4 |
|
Registered User
Join Date: Nov 2009
Location: Parachute, CO
Posts: 183
|
Re: bench seat question
You have the non fold brackets. The folding brackets have a stop to keep it from falling back. The brackets are part of the backrest seat. I just went through this in my Crew cab. The rear seat was shot but the front was good. I put the front in the rear for now and buckets up front with a console. At some point I will re-upholster the rear and get the folding seat back.
__________________
1984 1ton 4x4 crew cab dually 6.2 diesel,465,205,D60,D70,1987 3/4ton 4x4 suburban 5.7 FI350,TH400,208,1985 CJ-7 FI406,465,205,D60,FF14, 1970 Jeepster 350,465,205,D44,FF14, |
|
|
|
|
07-10-2016, 02:27 PM
|
#5 |
|
Registered User
Join Date: Aug 2013
Location: Calgary Alberta
Posts: 273
|
Re: bench seat question
Folding seat was optional on base trucks
|
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
