Precision window seals - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ItWillBeSlow · 03-19-2016, 09:26 PM

Bought an 8 piece window seal kit from one of the vendors here, was surprised to see the felt strip for the top/back is way too long and will require cutting.

Also, the division bar piece is over twice the needed length and will require cutting too. Since it has metal in it its more than just a box cutter. Did I get the wrong pieces? Quality looks great aside from the fact that I have to modify it right out of the package

48richard · 03-19-2016, 11:18 PM

These pieces extend down inside the door for the glass to slide in when it is down.
They are not too long.

ItWillBeSlow · 03-20-2016, 08:13 AM

Oh duh.. Should have thought of that.

What about the upper piece? Am I missing anything here? It's about a foot too long but will be an easy cut.

**special-K** · 03-20-2016, 08:59 AM

I don't think you should have to cut anything. The window channel needs to extend to the lowest point of the window lowered

ItWillBeSlow · 03-21-2016, 10:08 PM

The felt channel for the top/back part of the window is definitely longer than stock. It has cuts in the rubber for where the curve is, so it can't be installed backwards, and it's a good foot longer than needed. It extends past the top of the vent window. I wish I took a pic for comparison

trkfrk · 03-21-2016, 10:18 PM

Precision seals are good quality.. I did up trimming my felt about 1/4".

**GMCPaul** · 03-22-2016, 06:20 AM

Quote:

Originally Posted by ItWillBeSlow

The felt channel for the top/back part of the window is definitely longer than stock. It has cuts in the rubber for where the curve is, so it can't be installed backwards, and it's a good foot longer than needed. It extends past the top of the vent window. I wish I took a pic for comparison

felt channel for the top/back part of the window is a Left=Right part, turn the other end towards the vent window and you'll find the notches for the door curve align with the door glass upper frame curve.
You need to take the vent window out & door glass to install the glass run channel & division bar felts. Once you remove these you'll easily see where your mistaken on the division bar & glass run channel being to long. If you still feel something's to long after removing the items needed to replace these part's then post a picture showing the measurement of the glass run channel & division bar felts and I'll be happy to confirm the measurements for you.
Paul Jr. @ GMCPauls

ItWillBeSlow · 03-22-2016, 10:19 PM

Quote:

Originally Posted by GMCPaul

felt channel for the top/back part of the window is a Left=Right part, turn the other end towards the vent window and you'll find the notches for the door curve align with the door glass upper frame curve.
You need to take the vent window out & door glass to install the glass run channel & division bar felts. Once you remove these you'll easily see where your mistaken on the division bar & glass run channel being to long. If you still feel something's to long after removing the items needed to replace these part's then post a picture showing the measurement of the glass run channel & division bar felts and I'll be happy to confirm the measurements for you.
Paul Jr. @ GMCPauls

Good deal, thanks Paul

Norcalsully · 10-05-2016, 06:37 AM

Anybody run into trouble fitting the scraper seals into place?? I got the deluxe versions with the metal bead scraper; seems too long. Fits at the vent window, all clips line up, but it seems like too much strip running into the glass run opposite the vent window.

Robznob11 · 10-05-2016, 07:00 AM

The only thing I had to trim was the small felt at the bottom of the glass about 1/4" . As far as everything else you can put it in place with the glass in place. I did put the channel run in the vent before installing on one side and it's easier. But I forgot on the other side and was still able to install it relatively easy. Window down..install channel up and around. Then roll window up and install lower part. Loosen everything up to give yourself wiggle room. I used a long blunt nose screwdriver to push it in the middle and it pops right in. Just make sure not to use anything sharp and poke a hole. The whole trick to redoing these Doors is to Loosen everything so the window has room to move forward and back...hope this helps

03-19-2016, 09:26 PM	#1
ItWillBeSlow Registered User Join Date: May 2013 Location: You're the only 10 I see Posts: 367	Precision window seals Bought an 8 piece window seal kit from one of the vendors here, was surprised to see the felt strip for the top/back is way too long and will require cutting. Also, the division bar piece is over twice the needed length and will require cutting too. Since it has metal in it its more than just a box cutter. Did I get the wrong pieces? Quality looks great aside from the fact that I have to modify it right out of the package Attached Images __________________ 1972 C20

03-19-2016, 11:18 PM	#2
48richard Registered User Join Date: Oct 2009 Location: Phoenix, AZ Posts: 475	Re: Precision window seals These pieces extend down inside the door for the glass to slide in when it is down. They are not too long. __________________ 1971 C10 Longbed, 350/TH350

03-20-2016, 08:13 AM	#3
ItWillBeSlow Registered User Join Date: May 2013 Location: You're the only 10 I see Posts: 367	Re: Precision window seals Oh duh.. Should have thought of that. What about the upper piece? Am I missing anything here? It's about a foot too long but will be an easy cut. __________________ 1972 C20

03-20-2016, 08:59 AM	#4
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	Re: Precision window seals I don't think you should have to cut anything. The window channel needs to extend to the lowest point of the window lowered __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

03-21-2016, 10:08 PM	#5
ItWillBeSlow Registered User Join Date: May 2013 Location: You're the only 10 I see Posts: 367	Re: Precision window seals The felt channel for the top/back part of the window is definitely longer than stock. It has cuts in the rubber for where the curve is, so it can't be installed backwards, and it's a good foot longer than needed. It extends past the top of the vent window. I wish I took a pic for comparison __________________ 1972 C20

03-21-2016, 10:18 PM	#6
trkfrk Registered User Join Date: Jul 2010 Location: Las Vegas, NV Posts: 969	Re: Precision window seals Precision seals are good quality.. I did up trimming my felt about 1/4". __________________ Mark 1972 C10 SWB LS1/T56 6 speed trans/4:56 posi with 5.5"-7" static drop/Boss 338 Wheels 18"x20" My build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=424609. My first start up http://youtu.be/R899YQ1OcjU

10-05-2016, 06:37 AM	#9
Norcalsully Registered User Join Date: Apr 2015 Location: San Francisco, CA Posts: 21	Re: Precision window seals Anybody run into trouble fitting the scraper seals into place?? I got the deluxe versions with the metal bead scraper; seems too long. Fits at the vent window, all clips line up, but it seems like too much strip running into the glass run opposite the vent window.

10-05-2016, 07:00 AM	#10
Robznob11 Registered User Join Date: Feb 2004 Location: brownfield texas (west texas) Posts: 1,936	Re: Precision window seals The only thing I had to trim was the small felt at the bottom of the glass about 1/4" . As far as everything else you can put it in place with the glass in place. I did put the channel run in the vent before installing on one side and it's easier. But I forgot on the other side and was still able to install it relatively easy. Window down..install channel up and around. Then roll window up and install lower part. Loosen everything up to give yourself wiggle room. I used a long blunt nose screwdriver to push it in the middle and it pops right in. Just make sure not to use anything sharp and poke a hole. The whole trick to redoing these Doors is to Loosen everything so the window has room to move forward and back...hope this helps __________________ The Ghost 67 short wide full custom. 550 hp LSX, 4l80E, narrowed 9". Body dropped w/air ride! ........................ ___ .........________//__{\_____ ,,,,,,,/__(⊙)___//___/__(O)_/ @disciple2.rc 💪instagram💪 LED TAILS Last edited by Robznob11; 10-05-2016 at 07:07 AM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.