|
10-04-2016, 01:18 AM
|
#1 |
|
Registered User
Join Date: Jul 2015
Location: Whittier, CA
Posts: 851
|
Door bumpers?
Never seen these before, I have a 63. Where the heck do these go? Thanks
|
|
|
|
10-04-2016, 02:14 AM
|
#2 |
|
Registered User
Join Date: Jun 2014
Location: Glendora CA -> Tampa FL
Posts: 587
|
Re: Door bumpers?
Two bumpers go on each side along the door jamb. There should be 2 holes, one near the top and one near the bottom.
The 60-63 uses a bumper that fits a 1/4" hole while the 64-66 bumper fits into a 1/2" hole. Not sure which door bumpers those are pictured unless they are made to fit both hole sizes.
__________________
1966 C10 Short Fleetside 1988 Sportster, 2008 Street Glide Ken's 1966 C10 build "Red Ale" Follow on Instgram: @cv_performance https://instagram.com/cv_performance Harley Performance Parts: CV Performance (Harley related) Enjoying the ride! Last edited by Kenfuzed; 10-04-2016 at 03:33 AM. |
|
|
|
|
10-04-2016, 07:08 AM
|
#3 |
|
Registered User
Join Date: Sep 2012
Location: Leander, TX
Posts: 969
|
Re: Door bumpers?
I believe these are the ones for 1/2" holes. I ordered these for my 64', only to find out mine has 1/4" holes.
Bret
__________________
64' Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=586955 |
|
|
|
|
10-04-2016, 11:23 AM
|
#4 | |
|
Registered User
Join Date: Jun 2014
Location: Glendora CA -> Tampa FL
Posts: 587
|
Re: Door bumpers?
Quote:
__________________
1966 C10 Short Fleetside 1988 Sportster, 2008 Street Glide Ken's 1966 C10 build "Red Ale" Follow on Instgram: @cv_performance https://instagram.com/cv_performance Harley Performance Parts: CV Performance (Harley related) Enjoying the ride! |
|
|
|
|
|
10-04-2016, 12:26 PM
|
#5 |
|
Registered User
Join Date: Feb 2012
Location: pleasant valley--placerville ca
Posts: 3,039
|
Re: Door bumpers?
My 61 had none and there were no holes either. cab was blasted to bare metal, so i would of found the holes.
__________________
1961 chevy K10 my build is------------61K10 build |
|
|
|
|
10-05-2016, 01:53 AM
|
#6 | |
|
Registered User
Join Date: Jul 2015
Location: Whittier, CA
Posts: 851
|
Re: Door bumpers?
Quote:
Thank you for your response, I looked at my door jam and I could find any holes, unless I'm just not looking right. Where exactly are they supposed to be, do u have a picture? Thanks |
|
|
|
|
|
10-05-2016, 01:55 AM
|
#7 | ||
|
Registered User
Join Date: Jul 2015
Location: Whittier, CA
Posts: 851
|
Re: Door bumpers?
Quote:
Quote:
|
||
|
|
|
|
10-05-2016, 07:42 AM
|
#8 |
|
Registered User
Join Date: Sep 2012
Location: Leander, TX
Posts: 969
|
Re: Door bumpers?
In this pic you can see one a few inches up in the White part. The other one is down in the belt line area. I know others have said 64-66 should be a 1/2" hole but mine is 1/4".
 IMG_20160926_214135 by bjohnson388, on Flickr
__________________
64' Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=586955 |
|
|
|
|
10-05-2016, 12:12 PM
|
#9 | |
|
Registered User
Join Date: Jul 2015
Location: Whittier, CA
Posts: 851
|
Re: Door bumpers?
Quote:
So these bumpers, how good of a purpose do they serve? Are these ideal to have? And do they make any difference? I would like to assume so, for a fact, my door does make a lot of noise when I'm driving, it moves around a lot like if it was loose in the closed position, I've already tried adjusting the latch |
|
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
