tilt steering for our trucks, aftermarket or later model swap ins? - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Trap62 · 10-07-2014, 02:25 PM

Quote:

Originally Posted by mikke1

Was wondering if a 64 impala steering column will work on a 64 c10 pick up truck

Here's a thread showing a '64 Impala column going into a '66 -- might help...

http://67-72chevytrucks.com/vboard/s...64&postcount=8

wahl4m · 10-07-2014, 10:15 PM

i just installed a "flaming river" tilt in a 66 carryall ,nice unit,shifter dont have enough travel ,got a after makret linkage kit ,should work OK ? only thing that bothers me is the tilt should have 1 more upward tilt position ??? anybody notice that ? i used the uo joints with the column -BOY ARE THEY NICE AND HEAVY-DUTY !!

mikke1 · 10-07-2014, 11:38 PM

Thanks....

ol_skool_chevy · 10-08-2014, 12:22 AM

Anybody ever try a 73-78 tilt steering into a 64-66??
I want my key in the column and locking wheel....

**pdxhall** · 10-08-2014, 05:32 AM

I'm in the process of putting a 71 Camaro floor shift tilt column in my truck right now. I does take a bit of fabricating to make it work especially since I am moving it back so I have a little more room for my big belly. I pie cut and bent the 71 mount to fit and I am in the process of cutting and fitting the original mount so I still have the emergency brake and stop light switch in the original location.

Caraudiotekk · 10-08-2016, 10:46 AM

Finding van columns is a pretty hard task I'm finding..

**Chevy Fleetside** · 10-08-2016, 12:07 PM

Quote:

Originally Posted by Caraudiotekk

Finding van columns is a pretty hard task I'm finding..

Did you try Pick n Pull. I was lucky and got one on 25% off day and paid about $28 for it. It was a few years ago though.

Caraudiotekk · 10-08-2016, 12:45 PM

Quote:

Originally Posted by Chevy Fleetside

Did you try Pick n Pull. I was lucky and got one on 25% off day and paid about $28 for it. It was a few years ago though.

Just on the web hunt... Viking is next for me... Thanks for the reply. Just trying to stop my hemorrhaging from this ls swap

gnhuntin · 10-10-2016, 02:59 PM

Quote:

Originally Posted by tincan1966

I have a '94 C1500 column in my '65. Not a bad swap, but does require a bit of fab work. I converted my wipers to the turn signal mounted switch for delay control.
The shift lever on the 88 and up columns is reversed from the older style, so I fabbed my own cable operated shifter for the TH350C trans.

As someone posted earlier, The 3 speed auto columns and 4 speed auto columns have different detent spacing, and do not normally line up correctly when trying to adjust linkage. It is possible to actually hurt the trans do to improper gear engagement from a mis-aligned linkage. If you cannot select all the gears, then it is not set up right.

Do you have wiper delay, if so, how did you accomplish it? I think I read somewhere the delay is built in the wiper motor.

64shortbox · 10-10-2016, 07:37 PM

I was able to get a 72 Van tilt for my 64 off eBay for around $119.00 with shipping. The seller had lousy pictures, I could tell the shift indicator needle was broken but it was otherwise complete. I bought the tilt specific needle for around $9.00 and a new P R N D 2 1 lens while I was at it. I did have to move the Neutral Safety switch further down the column towards the firewall but a pretty straight forward installation. I also slid the column down as close to the dash as I possibly could to gain a little more gut room. Unfortunately I just couldn't stop there I also had to add a 73 Power Disc brake pedal and a 72 suspended gas pedal after adding Power Disc Brakes. These things are NEVER done!

earl84 · 10-11-2016, 08:08 AM

You may be able to find a tilt column out of an RV also. I found one that did not have the key on the column, so I could have a stock-ish look. Did the same things as 64shortbox and it is very comfortable to drive.

Caraudiotekk · 10-12-2016, 01:52 AM

Quote:

Originally Posted by 64shortbox

I was able to get a 72 Van tilt for my 64 off eBay for around $119.00 with shipping. The seller had lousy pictures, I could tell the shift indicator needle was broken but it was otherwise complete. I bought the tilt specific needle for around $9.00 and a new P R N D 2 1 lens while I was at it. I did have to move the Neutral Safety switch further down the column towards the firewall but a pretty straight forward installation. I also slid the column down as close to the dash as I possibly could to gain a little more gut room. Unfortunately I just couldn't stop there I also had to add a 73 Power Disc brake pedal and a 72 suspended gas pedal after adding Power Disc Brakes. These things are NEVER done!

Beautiful job! Thanks for the reply and sharing your pictures.

Caraudiotekk · 10-12-2016, 01:52 AM

Quote:

Originally Posted by earl84

You may be able to find a tilt column out of an RV also. I found one that did not have the key on the column, so I could have a stock-ish look. Did the same things as 64shortbox and it is very comfortable to drive.

Thank you

10-07-2014, 10:15 PM	#27
wahl4m Registered User Join Date: Jan 2002 Location: norwalk,iowa,usa Posts: 921	Re: tilt steering for our trucks, aftermarket or later model swap ins? i just installed a "flaming river" tilt in a 66 carryall ,nice unit,shifter dont have enough travel ,got a after makret linkage kit ,should work OK ? only thing that bothers me is the tilt should have 1 more upward tilt position ??? anybody notice that ? i used the uo joints with the column -BOY ARE THEY NICE AND HEAVY-DUTY !!

10-07-2014, 11:38 PM	#28
mikke1 Registered User Join Date: Oct 2014 Location: Bakersfield, Ca Posts: 22	Re: tilt steering for our trucks, aftermarket or later model swap ins? Thanks....

10-08-2014, 12:22 AM	#29
ol_skool_chevy Registered User Join Date: May 2010 Location: Hillsboro, Oregon 97123 Posts: 1,300	Re: tilt steering for our trucks, aftermarket or later model swap ins? Anybody ever try a 73-78 tilt steering into a 64-66?? I want my key in the column and locking wheel.... __________________ Measure with a yard stick Mark with Chalk Cut with a torch Built it yourself, don't count on others to to do it for you or with you. It will never get done

10-08-2014, 05:32 AM	#30
pdxhall Senior Member Join Date: Mar 2011 Location: Tucson, Arizona Posts: 2,084	Re: tilt steering for our trucks, aftermarket or later model swap ins? I'm in the process of putting a 71 Camaro floor shift tilt column in my truck right now. I does take a bit of fabricating to make it work especially since I am moving it back so I have a little more room for my big belly. I pie cut and bent the 71 mount to fit and I am in the process of cutting and fitting the original mount so I still have the emergency brake and stop light switch in the original location. __________________ Sanity'66 http://67-72chevytrucks.com/vboard/s...d.php?t=515110 Long bed, Fleetside, Small back window I've Done So Much, With So Little, For So Long, That Now I Can Do Anything With Nothing.

10-08-2016, 10:46 AM	#31
Caraudiotekk Registered User Join Date: Sep 2016 Location: Land of the Lost Posts: 39	Re: tilt steering for our trucks, aftermarket or later model swap ins? Finding van columns is a pretty hard task I'm finding..

10-10-2016, 07:37 PM	#35
64shortbox Registered User Join Date: Jan 2011 Location: Tulare, CA Posts: 734	Re: tilt steering for our trucks, aftermarket or later model swap ins? I was able to get a 72 Van tilt for my 64 off eBay for around $119.00 with shipping. The seller had lousy pictures, I could tell the shift indicator needle was broken but it was otherwise complete. I bought the tilt specific needle for around $9.00 and a new P R N D 2 1 lens while I was at it. I did have to move the Neutral Safety switch further down the column towards the firewall but a pretty straight forward installation. I also slid the column down as close to the dash as I possibly could to gain a little more gut room. Unfortunately I just couldn't stop there I also had to add a 73 Power Disc brake pedal and a 72 suspended gas pedal after adding Power Disc Brakes. These things are NEVER done! Attached Images

10-11-2016, 08:08 AM	#36
earl84 Registered User Join Date: Aug 2011 Location: Montrose, CO Posts: 972	Re: tilt steering for our trucks, aftermarket or later model swap ins? You may be able to find a tilt column out of an RV also. I found one that did not have the key on the column, so I could have a stock-ish look. Did the same things as 64shortbox and it is very comfortable to drive.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.