5.3 with sm465 4 speed?

[Hewfil1]

Originally Posted by MalibuSSwagon

I did this swap on my C10. 5.3L with a SM465. I am not privy to the programming changes needed as I just sent the PCM off to be programmed by the LT1swap.com guy. But I assume it involved deleting all the auto trans related stuff, and likely a manual trans spark table pasted in. It's not as smooth as it could be when getting on and off the gas be that's because I don't have a VSS hooked up. Once I get the TKO in I should have the VSS working and we'll see then.

Yes there is a spot for the pilot bearing in the 5.3L crank.

As far as hardware I used:

Flywheel - Sachs NFW1050
Clutch kit - Exedy 04081
Flywheel to crank bolts - ARP 330-2802
Pressure plate bolts - ARP 134-2201
Pilot bearing - GM 12557583

I used the ARP hardware since it was about the same price or a little more than the OEM GM hardware. The Exedy kit comes with throwout bearing and holds the power just fine, feels like a stock clutch. Towed 7k lbs no issue. The SM465 was factory installed in my truck, with the 1" setback plates (Car shop CSP2370) no driveline mods were needed. Any other questions just ask.

Whenever you get the TKO and VSS hooked up, just let me know what needed done and that should be it.

[MalibuSSwagon]

I don't plan on having the PCM reprogrammed when I put the TKO in, the speed signal doesn't matter much when you have a manual trans unless you are running a electronic speedo. Since I'm running the cable drive speedo off the trans the PCM just needs to see a speed signal to left it know it's off idle and adjust. TKO has both cable drive and a Ford 11 pulse VSS so I'll have a signal to send to the PCM.

[Hewfil1]

Originally Posted by MalibuSSwagon

I don't plan on having the PCM reprogrammed when I put the TKO in, the speed signal doesn't matter much when you have a manual trans unless you are running a electronic speedo. Since I'm running the cable drive speedo off the trans the PCM just needs to see a speed signal to left it know it's off idle and adjust. TKO has both cable drive and a Ford 11 pulse VSS so I'll have a signal to send to the PCM.

Ah, alright.

[Hewfil1]

Originally Posted by MalibuSSwagon

I don't plan on having the PCM reprogrammed when I put the TKO in, the speed signal doesn't matter much when you have a manual trans unless you are running a electronic speedo. Since I'm running the cable drive speedo off the trans the PCM just needs to see a speed signal to left it know it's off idle and adjust. TKO has both cable drive and a Ford 11 pulse VSS so I'll have a signal to send to the PCM.

Also forgot to ask, for your parts bought. Is that all of them? I just want a full parts list if you could so I can buy what I need a little at a time as I get paid.

[Hewfil1]

Originally Posted by Hewfil1

Also forgot to ask, for your parts bought. Is that all of them? I just want a full parts list if you could so I can buy what I need a little at a time as I get paid.

Side note:
My motor is an LM7 from a 2001 Silverado 1500.

[MalibuSSwagon]

Yes those are the transmission related parts you'll need. Stock linkage and fork works. Also if you haven't bought motor mounts yet, I would recommend CarShop CSP2370 plates, they are of the 1" setback design and place the motor in the right spot, you will not have to modify your driveline if you are using the stock SM465.

[Hewfil1]

Originally Posted by MalibuSSwagon

Yes those are the transmission related parts you'll need. Stock linkage and fork works. Also if you haven't bought motor mounts yet, I would recommend CarShop CSP2370 plates, they are of the 1" setback design and place the motor in the right spot, you will not have to modify your driveline if you are using the stock SM465.

Thank you so very much.