|
03-17-2004, 11:46 AM
|
#1 |
|
2.5/4 on 20's
Join Date: Aug 2001
Location: Shreveport, LA
Posts: 392
|
Dana 60 question
I'm looking for the Dana 60's that will bolt into our trucks. My question is what model of truck sould I look for that has them?
Any other information or pictures of 60's would also be helpful.
__________________
62 C/10 SWB. Currently in ground up resto. Big back window cab, V8, auto. My wife's grandfather's truck. 1965 Mustang Vert - Shelby Clone 2005 Dodge SRT-10 My Old 72 SWB |
|
|
|
03-17-2004, 12:04 PM
|
#2 |
|
user # 2756
 
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
Any chevy dana 60 will fit. Available 77 and up. There are single and dually dana 60s. The hub is different. The easy way to identify a front dana 60 is it only has 3 u-bolts holding the axle to the springs (has 2 studs for one side).
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm 
|
|
|
|
|
03-17-2004, 12:24 PM
|
#3 |
|
2.5/4 on 20's
Join Date: Aug 2001
Location: Shreveport, LA
Posts: 392
|
How much am I looking at spending on these if I find one?
__________________
62 C/10 SWB. Currently in ground up resto. Big back window cab, V8, auto. My wife's grandfather's truck. 1965 Mustang Vert - Shelby Clone 2005 Dodge SRT-10 My Old 72 SWB |
|
|
|
|
03-17-2004, 05:43 PM
|
#4 |
|
Registered User
Join Date: Jun 2003
Location: spokane wa
Posts: 2,189
|
Front D60's can range from finding one for free (a miracle) to brand new of over 2000.00
most average used fronts go for 800-1500. Good luck
__________________
Support The Board |
|
|
|
|
03-17-2004, 06:30 PM
|
#5 |
|
Registered User
Join Date: Feb 2003
Location: The Rubber City
Posts: 5,498
|
try looking around before you look for just the axle. sometimes you can buy a crappy and rusty K/30 for cheap then part it out and make $$$. Most common configuration I've seen is 454/TH400/NP205, with the D60 front and 14bff rear, and all these parts are (obviously) desireable.
__________________
1969 GMC K2500  1996 Honda Accord 2007 Kawasaki KLR 650 Last edited by 1969 GMC; 03-17-2004 at 08:39 PM. |
|
|
|
|
03-18-2004, 01:10 PM
|
#6 |
|
Broke
Join Date: Aug 2001
Location: West Plains,MO
Posts: 385
|
My Dana 60 came out of an old 1985 military 1 ton. It fit just perfect. Price can range like drink2mny said.
__________________
72CheyenneSuper1ton4x4BigBlock Last edited by Bram; 03-19-2004 at 11:15 AM. |
|
|
|
|
03-18-2004, 09:10 PM
|
#7 |
|
user # 2756
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
Someone locally(SE VA) is selling one with 4.56 gears, rotor to rotor for $1200 firm. If you want I'll get you the number.
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm
|
|
|
|
|
03-18-2004, 11:50 PM
|
#8 |
|
Registered User
Join Date: Dec 2003
Location: Pampa Texas
Posts: 36
|
So far everyone is right about the prices. A rebuildable D 60 front starts at about $800. I got this one for that and it had good internals and that was it. I replaced everything but the r&p and the axle shafts. I had to cut the axle u-joints out with a gas hatchet to replace them. It cost me around $500 at Orealiys to make it road worthy.
 Here it is installed in the truck. 
|
|
|
|
|
03-19-2004, 12:32 AM
|
#9 |
|
" SHOW ME"
Join Date: Jan 2003
Location: shelbyville illinois
Posts: 2,624
|
i sold 2 of them last year , complete running and driving k30's with the combo stated above , 454 th400 205 d 60 front 14 bolt rear , 2500 apiece , very rusty they were both single wheel trucks , ive got a line on a dually back in the weeds , just waitin to save the cash
|
|
|
|
|
03-19-2004, 02:44 AM
|
#10 |
|
Registered User
Join Date: Aug 2003
Location: Crawfordsville,Oregon
Posts: 83
|
I recently bought my 60 front 14 bolt rear combo with 4:10 gears for 400 bucks. I think I got a better then adverage deal though. They came out of a 80 k30. I installed the front end no problem, just had to get differnt spring plates and brake lines. The rear I have to narrow the spring pads a touch but otherwise shouldnt be a problem.
__________________
Are we there yet? |
|
|
|
|
03-29-2004, 01:41 AM
|
#11 |
|
Currently Blazerless
Join Date: Apr 2000
Location: St. Joseph Mo.
Posts: 4,828
|
redneck_motorsports, looks like your building a pretty tuff 68, you got any more pics to share.
|
|
|
|
|
03-29-2004, 01:52 AM
|
#12 |
|
Registered User
Join Date: Dec 2003
Location: Pampa Texas
Posts: 36
|
You can see all the pics of this build up in the "Fire Truck" album.
http://www.texas4x4.org/gallery/redneckmtrsprts |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
