|
01-14-2017, 01:24 PM
|
#1 |
|
Registered User
Join Date: Dec 2016
Location: Farmington, Ca.
Posts: 151
|
Door corner patch
I have seen them online, can't find now for some reason. The little lower inner corners where the seal goes. Where did I see them?
__________________
56' 3100 shortbed |
|
|
|
01-14-2017, 10:58 PM
|
#2 |
|
Registered User
Join Date: Sep 2014
Location: Riverside, CA
Posts: 9
|
Re: Door corner patch
Have you looked on LMC Truck?
|
|
|
|
|
01-15-2017, 12:04 PM
|
#3 |
|
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,342
|
Re: Door corner patch
A pic and/or a yearseries would help. Inner, outer, front or rear of door would also help.
|
|
|
|
|
01-15-2017, 07:49 PM
|
#4 |
|
Registered User
Join Date: Dec 2016
Location: Farmington, Ca.
Posts: 151
|
Re: Door corner patch
Yep checked LMC, Saw them somewhere 56' 3100
__________________
56' 3100 shortbed |
|
|
|
|
01-15-2017, 08:04 PM
|
#5 |
|
Registered User
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
|
Re: Door corner patch
That looks easy enough to make from scratch.
Brian
__________________
1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings" |
|
|
|
|
01-16-2017, 01:45 PM
|
#6 |
|
Registered User
Join Date: Sep 2014
Location: Riverside, CA
Posts: 9
|
Re: Door corner patch
check these out
https://www.c2cfabrication.com/produ...FdWNfgodH8oLKg
__________________
1959 Apache 3100 Fleetside short bed 235 l6 |
|
|
|
|
01-16-2017, 01:48 PM
|
#7 | |
|
Registered User
Join Date: Sep 2014
Location: Riverside, CA
Posts: 9
|
Re: Door corner patch
Quote:
https://www.c2cfabrication.com/produ...oor-skin-patch
__________________
1959 Apache 3100 Fleetside short bed 235 l6 |
|
|
|
|
|
01-16-2017, 03:29 PM
|
#8 |
|
Registered User
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,342
|
Re: Door corner patch
I would suggest a little sandblast treatment of the back side of the door skin while you have the part cut off and before welding in the new part. are you doing the whole lower, front to rear, or just a patch made from the new panel?
|
|
|
|
|
01-17-2017, 11:41 AM
|
#9 |
|
Registered User
Join Date: Dec 2016
Location: Farmington, Ca.
Posts: 151
|
Re: Door corner patch
Made one as mentioned, I saw the whole panels, thought I had seen just the corner somewhere. Thanks
__________________
56' 3100 shortbed |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
