Is my 350 on the outs? - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

tommy3horse · 12-19-2016, 07:46 PM

Update; the weather broke to the point where I could move things around and pull the expired engine today. 30 degrees is way better than the single digits over the weekend round here. Gonna clean things up a bit and ready things for the crate to go in on Thursday.

tommy3horse · 12-31-2016, 09:57 PM

Had the time this week to put everything back on the motor. Today, I got the engine oil system primed, fitted the dipstick and installed the intake and valve covers. Tomorrow it goes back in the truck, and if all goes well I will attempt to bring it to life. Looks decent to boot

tommy3horse · 01-23-2017, 06:56 PM

Alrighty, I finally got everything bolted up and worked out the kinks, like a vacuum leak and leaking heater core. Put a decent initial tune on it and have logged a whopping 170 miles so far. No leaks on the motor, but the p steering hose is dripping a bit at the pump and probably needs replaced. Runs really well!
Tom

hamjet · 01-23-2017, 08:11 PM

Great news! glad everything turned out OK. it looks great too...

tommy3horse · 01-27-2017, 06:43 PM

UPDATE:
Have driven a very easy 200 miles, runs great, but rear main appears to be leaking. Anyone know the process for getting this repair started via the warranty?
Thanks,
Tom

hamjet · 01-27-2017, 08:21 PM

check a few things first. maybe leaking at the oil pressure sending unit behind the intake, the rear intake gasket, or in back of the valve cover gasket, could appear to be a rear main seal. retorque the pan gasket also..

tommy3horse · 01-29-2017, 11:12 AM

Thanks Hamjet, it's Sunday and I have the time today to check those things...
T

tommy3horse · 02-01-2017, 06:55 PM

Hello,
Joe, you were on it! I pulled the converter/flywheel cover and it was dry as was the back end of the crank area. I found the valve cover bolts very loose and a trail of motor oil which must have blown away from the block and landed on the trans cooler lines, fill tube inspection cover on the outside.
I watched my old 350 drip outta the rear main and (everywhere else)for 2 years and it looked very similar.

Thanks again,

Tom

BTW the old motor has a steel crank and KB pistons, cylinders look to be .020 over bored. Wonder what's up with that, and it has 2 bolt mains...?

hamjet · 02-01-2017, 07:42 PM

Very good, you must be a happy camper now. on the older engine, there's nothing wrong with 2 bolt mains. they're good for 7000 RPMs, I've never seen the crank rip out the bottom end from people using 2 bolt mains in moderately built HP engines...

tommy3horse · 02-01-2017, 07:55 PM

A steel crank tho...?

12-19-2016, 07:46 PM	#26
tommy3horse Registered User Join Date: Feb 2015 Location: St. Clair, Missouri Posts: 122	Re: Is my 350 on the outs? Update; the weather broke to the point where I could move things around and pull the expired engine today. 30 degrees is way better than the single digits over the weekend round here. Gonna clean things up a bit and ready things for the crate to go in on Thursday. Attached Images __________________ 1972 GMC C1500 350/350 1965 Mustang 2+2 289 4spd, show-car 1965 Mustang Coupe 289 4spd, stoplight racer 1/2 dozen Wheelhorse Tractors

12-31-2016, 09:57 PM	#27
tommy3horse Registered User Join Date: Feb 2015 Location: St. Clair, Missouri Posts: 122	Re: Is my 350 on the outs? Had the time this week to put everything back on the motor. Today, I got the engine oil system primed, fitted the dipstick and installed the intake and valve covers. Tomorrow it goes back in the truck, and if all goes well I will attempt to bring it to life. Looks decent to boot Attached Images __________________ 1972 GMC C1500 350/350 1965 Mustang 2+2 289 4spd, show-car 1965 Mustang Coupe 289 4spd, stoplight racer 1/2 dozen Wheelhorse Tractors

01-23-2017, 06:56 PM	#28
tommy3horse Registered User Join Date: Feb 2015 Location: St. Clair, Missouri Posts: 122	Re: Is my 350 on the outs? Alrighty, I finally got everything bolted up and worked out the kinks, like a vacuum leak and leaking heater core. Put a decent initial tune on it and have logged a whopping 170 miles so far. No leaks on the motor, but the p steering hose is dripping a bit at the pump and probably needs replaced. Runs really well! Tom Attached Images __________________ 1972 GMC C1500 350/350 1965 Mustang 2+2 289 4spd, show-car 1965 Mustang Coupe 289 4spd, stoplight racer 1/2 dozen Wheelhorse Tractors

01-23-2017, 08:11 PM	#29
hamjet Registered User Join Date: Apr 2013 Location: South Westerlo, New York Posts: 1,325	Re: Is my 350 on the outs? Great news! glad everything turned out OK. it looks great too... __________________ Thanks, Joe.. 1969 C/10, 348 C.I., 3X2 bbl. V8, 2004r , LWB.

01-27-2017, 06:43 PM	#30
tommy3horse Registered User Join Date: Feb 2015 Location: St. Clair, Missouri Posts: 122	Re: Is my 350 on the outs? UPDATE: Have driven a very easy 200 miles, runs great, but rear main appears to be leaking. Anyone know the process for getting this repair started via the warranty? Thanks, Tom __________________ 1972 GMC C1500 350/350 1965 Mustang 2+2 289 4spd, show-car 1965 Mustang Coupe 289 4spd, stoplight racer 1/2 dozen Wheelhorse Tractors

01-27-2017, 08:21 PM	#31
hamjet Registered User Join Date: Apr 2013 Location: South Westerlo, New York Posts: 1,325	Re: Is my 350 on the outs? check a few things first. maybe leaking at the oil pressure sending unit behind the intake, the rear intake gasket, or in back of the valve cover gasket, could appear to be a rear main seal. retorque the pan gasket also.. __________________ Thanks, Joe.. 1969 C/10, 348 C.I., 3X2 bbl. V8, 2004r , LWB.

01-29-2017, 11:12 AM	#32
tommy3horse Registered User Join Date: Feb 2015 Location: St. Clair, Missouri Posts: 122	Re: Is my 350 on the outs? Thanks Hamjet, it's Sunday and I have the time today to check those things... T __________________ 1972 GMC C1500 350/350 1965 Mustang 2+2 289 4spd, show-car 1965 Mustang Coupe 289 4spd, stoplight racer 1/2 dozen Wheelhorse Tractors

02-01-2017, 06:55 PM	#33
tommy3horse Registered User Join Date: Feb 2015 Location: St. Clair, Missouri Posts: 122	Re: Is my 350 on the outs? Hello, Joe, you were on it! I pulled the converter/flywheel cover and it was dry as was the back end of the crank area. I found the valve cover bolts very loose and a trail of motor oil which must have blown away from the block and landed on the trans cooler lines, fill tube inspection cover on the outside. I watched my old 350 drip outta the rear main and (everywhere else)for 2 years and it looked very similar. Thanks again, Tom BTW the old motor has a steel crank and KB pistons, cylinders look to be .020 over bored. Wonder what's up with that, and it has 2 bolt mains...? __________________ 1972 GMC C1500 350/350 1965 Mustang 2+2 289 4spd, show-car 1965 Mustang Coupe 289 4spd, stoplight racer 1/2 dozen Wheelhorse Tractors

02-01-2017, 07:42 PM	#34
hamjet Registered User Join Date: Apr 2013 Location: South Westerlo, New York Posts: 1,325	Re: Is my 350 on the outs? Very good, you must be a happy camper now. on the older engine, there's nothing wrong with 2 bolt mains. they're good for 7000 RPMs, I've never seen the crank rip out the bottom end from people using 2 bolt mains in moderately built HP engines... __________________ Thanks, Joe.. 1969 C/10, 348 C.I., 3X2 bbl. V8, 2004r , LWB.

02-01-2017, 07:55 PM	#35
tommy3horse Registered User Join Date: Feb 2015 Location: St. Clair, Missouri Posts: 122	Re: Is my 350 on the outs? A steel crank tho...? __________________ 1972 GMC C1500 350/350 1965 Mustang 2+2 289 4spd, show-car 1965 Mustang Coupe 289 4spd, stoplight racer 1/2 dozen Wheelhorse Tractors



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.