The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > Heavy Haulers

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-06-2017, 12:08 AM   #1
rkn463
Registered User
 
rkn463's Avatar
 
Join Date: Jan 2012
Location: Iredell, Texas
Posts: 582
Re: so i went and looked at this today

I think picture 3 is an electronic governor.

-Richard
__________________
I may have too many Chevys... Is that possible?
68 c50 pickup build: http://67-72chevytrucks.com/vboard/s...d.php?t=704713
rkn463 is offline   Reply With Quote
Old 03-08-2017, 10:51 PM   #2
sweetk30
Registered User
 
sweetk30's Avatar
 
Join Date: May 2012
Location: horseheads,ny rust belt
Posts: 2,794
Re: so i went and looked at this today

went and picked up the rad and pressure over flow tank today .

then motor/trans combo was ready at local ABF terminal .

next to the last parts order showed up today . just waiting on a clutch linkage piviot pin swivel .

hope to start tearing in to the stuff Thursday . going to reseal / clean the tranny first since he goes in first cause I don't have a med/heavy duty style tranny jack .

then it will be clean / reseal the engine and get ready for drop in .
Attached Images
  
__________________
77-k30lb BIG truck build .
87-k30lb budget beater build .
85-k30lb the plow machine build .
85-c10sb summer fun toy .
-----------------------------
HOLLEY SNIPER efi = worst case of p.i.t.a i ever had .

EDELBROCK pro flo 4 = best deal going so far . love my setup works great.
sweetk30 is offline   Reply With Quote
Old 03-09-2017, 07:13 PM   #3
sweetk30
Registered User
 
sweetk30's Avatar
 
Join Date: May 2012
Location: horseheads,ny rust belt
Posts: 2,794
Re: so i went and looked at this today

dam used motor is junk . . . . . tore in to it to clean and re gasket / seal it and the carb throttle shaft was frozen ( 1st oh sh!t ) then trail of water down intake runner ( 2nd oh sh!t ) and pull plugs and #1 solid rust ( 3rd oh sh!t ) and bore scope down plug hole has shown SOLID RUST and NO FU*KING GOOD AT ALL ! ! !

then to top it off the head guy in charge has just left yesterday on a 2 week vacation out of the country . so I have to wait on a refund on my credit card . . . .
__________________
77-k30lb BIG truck build .
87-k30lb budget beater build .
85-k30lb the plow machine build .
85-c10sb summer fun toy .
-----------------------------
HOLLEY SNIPER efi = worst case of p.i.t.a i ever had .

EDELBROCK pro flo 4 = best deal going so far . love my setup works great.
sweetk30 is offline   Reply With Quote
Old 03-09-2017, 08:22 PM   #4
Airdirect
Registered User
 
Join Date: Oct 2016
Location: Powderly Texas
Posts: 301
Re: so i went and looked at this today

Send your original motor to the machine shop for re-bore and have the heads reworked. You will then have a new motor that is dependable.
Airdirect is offline   Reply With Quote
Old 03-09-2017, 10:41 PM   #5
sweetk30
Registered User
 
sweetk30's Avatar
 
Join Date: May 2012
Location: horseheads,ny rust belt
Posts: 2,794
Re: so i went and looked at this today

I don't think its even going to take that . . .

pulled a valve cover and you can basicly eat off the inside of it . my buddy bore scoped the plug holes and all but 1 super clean . 1 has tinyest bit of powdered surface rust in 1 spot.

Friday its hanging on a engine stand and tearin the heads off . were going to find out the rest of the story as paul Harvey would say .
__________________
77-k30lb BIG truck build .
87-k30lb budget beater build .
85-k30lb the plow machine build .
85-c10sb summer fun toy .
-----------------------------
HOLLEY SNIPER efi = worst case of p.i.t.a i ever had .

EDELBROCK pro flo 4 = best deal going so far . love my setup works great.
sweetk30 is offline   Reply With Quote
Old 03-09-2017, 11:56 PM   #6
Airdirect
Registered User
 
Join Date: Oct 2016
Location: Powderly Texas
Posts: 301
Re: so i went and looked at this today

Amazon has a set of 8 pistons .030 or .060 oversize for $265.00. If you have a good block you can overhaul these fairly reasonable. Even if your bores are good, a new set of pistons will go a long way given you have new ring lands and you don't have to clean up the old pistons.

Last edited by Airdirect; 03-09-2017 at 11:57 PM. Reason: more info
Airdirect is offline   Reply With Quote
Old 03-10-2017, 10:51 AM   #7
ckfarm
Registered User
 
Join Date: Mar 2013
Location: buffalo lake,mn
Posts: 11
Re: so i went and looked at this today

I just had a 427 rebuilt -the engine kit was about $1050.00 included pistons,,rings,bearings,timing set,oil pump,cam and lifters and gaskets.Machine work-bore .030,polish crankshaft,plane heads,valve job,and assembly was about $1075.00 . So about $2200.00 total this should give you some comparison for what a total rebuild will be.
ckfarm is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:08 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com