|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
04-02-2004, 12:12 AM
|
#1 |
|
Registered User
Join Date: Jan 2002
Location: Calgary, Alberta, Canada
Posts: 451
|
Wire question - brown wire going to proportioning valve
What is the brown wire going to the proportioning valve on my 72 with power brakes? I am installing a new Painless Wiring harness into the entire truck, and there is no mention of this wire in the manual.
__________________
72 C10 Cheyenne Super Full trim Factory tach dash A/C dash Factory tilt 350 / 350 power train - with Edelbrock components. |
|
|
|
04-02-2004, 12:19 AM
|
#2 |
|
Registered User
Join Date: Feb 2004
Location: Massachusetts
Posts: 269
|
It's the brake failure warning switch.
__________________
72 Cheyenne Super 4x4 SWB |
|
|
|
|
04-02-2004, 12:22 AM
|
#3 |
|
On the road
  
Join Date: Jan 2004
Location: NATCHITOCHES LOUISIANA
Posts: 818
|
That's for the brake light in your dash. Not sure of all the ins and outs, I guess if you lose pressure ( I don't know how much pressure it takes to operate ) the light comes on.
Mike |
|
|
|
|
04-02-2004, 12:22 AM
|
#4 |
|
Registered User
Join Date: Feb 2004
Location: Massachusetts
Posts: 269
|
It should go to the ignition switch, and then to the cluster I think.
__________________
72 Cheyenne Super 4x4 SWB |
|
|
|
|
04-02-2004, 12:24 AM
|
#5 |
|
Registered User
Join Date: Feb 2004
Location: Massachusetts
Posts: 269
|
I think it is triggered by a large differential between front and rear brakes.
__________________
72 Cheyenne Super 4x4 SWB |
|
|
|
|
04-02-2004, 12:19 PM
|
#6 |
|
Registered User
Join Date: Feb 2000
Location: Georgetown, KY, USA
Posts: 631
|
There is a toggle switch inside of the Prop. valve with a diaphram that is pushed to either side by a large difference in pressure on one side or the other it grounds the signal and turns the light on. Also a grounding Emer. brake switch can be tied in to the wire to let you know that your E brake is....not that any of us have ever drove anywhere with our E Brake on!!!
|
|
|
|
|
04-02-2004, 12:24 PM
|
#7 |
|
Registered User
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,005
|
Yeah, mine came on when I had manual brakes right before they started going out on me (before the power brake swap). I was quite impressed that after 30 years it actually still worked.
__________________
1972 C20 Suburban- Big Blue Betty '56 Chevy Bel Air Sedan- Frame up Restoration -What would you attempt to achieve if you knew you could not fail?- -I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door- R.I.P. EAST SIDE LOW LIFE |
|
|
|
|
04-02-2004, 01:21 PM
|
#8 |
|
More Cowbell....
Join Date: Mar 2004
Location: Puckett, MS
Posts: 3,569
|
After 35 years, mine actually came on last November. All of the fluid from the front half of the master cylinder had leaked out, and I fired it up and moved it outside the garage. When I hit the brake, it went to the floor and the light came on. I was like....Woh!
__________________
There once was a member from Puckett.....Who ( fill in the blank blank blank ) bucket |
|
|
|
|
04-02-2004, 02:32 PM
|
#9 |
|
Wiseass secured himself a BAN
Join Date: Nov 2000
Location: MOON!!!
Posts: 2,282
|
How do you check it to see if it still works?
|
|
|
|
|
04-02-2004, 02:39 PM
|
#10 |
|
Beer Power!!!!!!!!!!
Join Date: Nov 2003
Location: Nacogdoches, TX
Posts: 280
|
To check if it still works, simply disconnect the wire from the valve.
I had to replace my prop valve because, I guess, the old one wore out. TIP: Your old proportioning valve makes an EXCELLENT trotline weight.
__________________
Rather be fishin' |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
