Vent Window to Door Skin Seals ??? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**samkost** · 04-13-2017, 07:31 PM

First off I would like to thank everyone for a great informative forum with your helpful replies to others and myself relating to the restoration of our trucks.

I've finally got my doors assembled with lots of research here and many thanks to Wes at Classic Heartbeat.

New Precision brand Cab to Door Seals.
A little snug on the drivers door closure but they are relaxing well.
New after market sport mirrors, regulators, door latches, locks and handles.
A few minor adjustments needed, the windows, latches, strikers and locks work smoothly. Whew!

Windows crank smoothly and work like new.

With concerns, aftermarket Vent Windows, Door Glass assmblies and Window felts installed and fit very well.

My question is about the outside lower Vent Windows to Door skin rubber seal.
After researching the forum for past threads I could use some help.
Does the seal overlap or butt up against the door skin?
Should they overlap the upper door skin like the Window felt trim?
I have a small gap presently because they are tucked down inside.
If someone can show me the correct way with a photo I would appreciate your advice and feedback.
Sorry I didn't get a real good close up of the gap.

Thanks again everyone,
Sam

**lolife99** · 04-13-2017, 09:55 PM

Your install is correct

**samkost** · 04-13-2017, 10:27 PM

That's great Keith!
I was hoping it was.

Thanks for the reply,
Sam

**HO455** · 04-14-2017, 12:54 AM

I had the same concerns when I did mine. It just looked wrong to be on the inside of the door. I even tried to glue mine down on the outside, but it just wouldn't stay put. I finally found the right thread that pointed out the error of my ways.

aod92 · 04-14-2017, 08:42 AM

I did the same thing. I left them on the outside at first but finally tucked them into the door.

67ChevyRedneck · 04-14-2017, 09:12 AM

The outside seal gets pinched between the door and vent window? I've always trimmed mine right a the window edge.

04-13-2017, 07:31 PM	#1
samkost Senior Member Join Date: Sep 2014 Location: Lake Tapps, Wa. Posts: 674	Vent Window to Door Skin Seals ??? First off I would like to thank everyone for a great informative forum with your helpful replies to others and myself relating to the restoration of our trucks. I've finally got my doors assembled with lots of research here and many thanks to Wes at Classic Heartbeat. New Precision brand Cab to Door Seals. A little snug on the drivers door closure but they are relaxing well. New after market sport mirrors, regulators, door latches, locks and handles. A few minor adjustments needed, the windows, latches, strikers and locks work smoothly. Whew! Windows crank smoothly and work like new. With concerns, aftermarket Vent Windows, Door Glass assmblies and Window felts installed and fit very well. My question is about the outside lower Vent Windows to Door skin rubber seal. After researching the forum for past threads I could use some help. Does the seal overlap or butt up against the door skin? Should they overlap the upper door skin like the Window felt trim? I have a small gap presently because they are tucked down inside. If someone can show me the correct way with a photo I would appreciate your advice and feedback. Sorry I didn't get a real good close up of the gap. Thanks again everyone, Sam Attached Images

04-13-2017, 09:55 PM	#2
lolife99 67-72 parts collector,… Join Date: Nov 2002 Location: Mid-MO Posts: 22,701	Re: Vent Window to Door Skin Seals ??? Your install is correct __________________ Keith Convert to disc brakes. http://67-72chevytrucks.com/vboard/s...d.php?t=444823

04-13-2017, 10:27 PM	#3
samkost Senior Member Join Date: Sep 2014 Location: Lake Tapps, Wa. Posts: 674	Re: Vent Window to Door Skin Seals ??? That's great Keith! I was hoping it was. Thanks for the reply, Sam

04-14-2017, 12:54 AM	#4
HO455 Post Whore Join Date: Feb 2016 Location: Portland Oregon Posts: 11,393	Re: Vent Window to Door Skin Seals ??? I had the same concerns when I did mine. It just looked wrong to be on the inside of the door. I even tried to glue mine down on the outside, but it just wouldn't stay put. I finally found the right thread that pointed out the error of my ways. __________________ Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help. RIP Bob Parks. 1967 Burban (the WMB),1988 S10 Blazer (the Stink10 II),1969 GTO (the Goat), 1970 Javelin, 1952 F2 Ford OHC six 4X4, 29 Model A, 72 Firebird (the DBP Bird). 85 Alfa Romeo If it breaks I didn't want it in the first place The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377

04-14-2017, 08:42 AM	#5
aod92 Registered User Join Date: Dec 2014 Location: Plainfield il. Posts: 643	Re: Vent Window to Door Skin Seals ??? I did the same thing. I left them on the outside at first but finally tucked them into the door.

04-14-2017, 09:12 AM	#6
67ChevyRedneck Hittin E-Z Street on Mud Tires Join Date: Nov 2004 Location: Greenville, SC Posts: 23,090	Re: Vent Window to Door Skin Seals ??? The outside seal gets pinched between the door and vent window? I've always trimmed mine right a the window edge. __________________ Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.